ASTM E 1077 : 2014 : REDLINE
Current
The latest, up-to-date edition.
Standard Test Methods for Estimating the Depth of Decarburization of Steel Specimens
English
21-03-2014
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 03.01, 2015 Defines procedures for estimating depth of decarburization of steels irrespective of the composition, matrix microstructure, or section shape.
| Committee |
E 04
|
| DocumentType |
Redline
|
| Pages |
11
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
1.1These test methods cover procedures for estimating the depth of decarburization of steels irrespective of the composition, matrix microstructure, or section shape. The following basic procedures may be used:
1.1.1Screening methods.
1.1.2Microscopical methods.
1.1.3Microindentation hardness methods.
1.1.4Chemical analysis methods.
1.2In case of a dispute, the rigorous quantitative or lineal analysis method (see 7.3.5 and 7.3.6) shall be the referee method. These methods can be employed with any cross-sectional shape. The chemical analytical methods generally reveal a greater depth of decarburization than the microscopical methods but are limited to certain simple shapes and by availability of equipment. These techniques are generally reserved for research studies. The microindentation hardness method is suitable for accurate measurements of hardened structures with relatively homogeneous microstructures.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| MIL-S-6758 Revision B:1993 | STEEL, CHROME-MOLYBDENUM (4130) BARS AND REFORGING STOCK (AIRCRAFT QUALITY) |
| SAE AMS6527F | Steel, Bars and Forgings 2.0Cr - 10Ni - 14Co - 1.0Mo (0.15 - 0.19C) Vacuum Melted, Normalized and Overaged |
| ASTM A 485 : 2017 : REDLINE | Standard Specification for High Hardenability Antifriction Bearing Steel |
| MIL-DTL-12560 Revision K:2013 | ARMOR PLATE, STEEL, WROUGHT, HOMOGENEOUS (FOR USE IN COMBAT-VEHICLES AND FOR AMMUNITION TESTING) |
| SAE AMS6411J | Steel Bars, Forgings, and Tubing 0.88Cr - 1.8Ni - 0.42Mo - 0.08V (0.28 - 0.33C) (4330 Mod) Consumable Electrode Remelted |
| SAE AMS6303J | Steel Bars and Forgings, Low Alloy, Heat-Resistant 0.65Si - 1.25Cr - 0.50Mo - 0.85V (0.25 - 0.30C) |
| SAE AMS6475K | Steel, Nitriding, Bars, Forgings, and Tubing 1.1Cr – 3.5Ni – 0.25Mo – 1.2Al (0.21 – 0.26C) |
| AGMA 2004 : C | GEAR MATERIALS, HEAT TREATMENT AND PROCESSING MANUAL |
| SAE AMS6408E | Steel, Hotwork Tool, Bars and Forgings 5.25Cr - 1.5Mo - 1.0V (0.35-0.45C) (H-13) Electroslag Remelted (ESR) or Consumable Electrode Vacuum Arc Remelted (VAR) Annealed |
| ASTM A 295 : 1998 | Standard Specification for High-Carbon Anti-Friction Bearing Steel |
| ASTM A 756 : 2017 : REDLINE | Standard Specification for Stainless Anti-Friction Bearing Steel |
| FF-O-601 Revision F:1990 | OPENERS, CAN, HAND AND MOUNTED |
| ASTM E 3 : 2011 : R2017 | Standard Guide for Preparation of Metallographic Specimens |
| SAE AMS6360M | Steel Tubing, Seamless 0.95Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130) Normalized or Stress Relieved |
| ASTM B 874 : 1996 : R2013 | Standard Specification for Chromium Diffusion Coating Applied by Pack Cementation Process |
| SAE AMS6348D | Steel, Bars 0.95Cr - 0.20Mo (0.28 to 0.33C) (SAE 4130) Normalized |
| ASTM B 874 : 1996 : R2003 | Standard Specification for Chromium Diffusion Coating Applied by Pack Cementation Process |
| ASTM B 874 : 1996 : R2008 | Standard Specification for Chromium Diffusion Coating Applied by Pack Cementation Process |
| ASTM E 3 : 2011 | Standard Guide for Preparation of Metallographic Specimens |
| SAE AMSS6758B | Steel, Chrome-Molybdenum (4130) Bars and Reforging Stock (Aircraft Quality) |
| A-A-52202 Revision C:2012 | OPENER, CAN, HAND, FOR SQUARE AND ROUND FOOD CANS |
| AGMA 942 : A2012(R2017) | METALLURGICAL SPECIFICATIONS FOR POWDER METALLURGY, PM, STEEL GEARING |
| SAE AMS6532F | Steel, Bars and Forgings 3.1Cr - 11.5Ni - 13.5Co - 1.2Mo (0.21 - 0.25C) Vacuum Melted, Normalized and Overaged Precipitaiton Hardenable |
| SAE AMS6558 | Steel, Bars, Wire, and Forgings 10.5 Mo - 6 W - 3.75 Cr - 2 V (1.25 - 1.40 C) Powder Metallurgy Product Hot Isostatically Pressed |
| AGMA 923 : B | METALLURGICAL SPECIFICATIONS OF STEEL GEARING |
| IFI 140 : 2000 | CARBON AND ALLOY STEEL WIRE, RODS AND BARS FOR MECHANICAL FASTENERS |
| SAE AMS6557 | Steel, Bars, Wire, and Forgings 9V - 5.25Cr - 1.3Mo (1.80 – 1.95C) Powder Metallurgy Product Hot Isostatically Pressed |
| SAE AMS6448L | Steel, Bars, Forgings, and Tubing 0.95Cr - 0.22V (0.48 – 0.53C) (SAE 6150) |
| SAE AMS6346B | Steel Bars 0.95Cr - 0.20Mo (0.28 to 0.33C) (SAE 4130) Hardened and Tempered, 125 Ksi (862 MPa) Tensile Strength |
| SAE AMS5352F | Steel, Corrosion-Resistant, Investment Castings 17Cr - 0.55Mo (0.95 - 1.20C) Annealed |
| SAE AMS6560 | Steel Bars, Wire and Forgings 10 Co - 7 Mo - 6 V - 6 W - 4 Cr (2.2 – 2.4C) Premium Aircraft-Quality for Bearing Applications Inert Gas Atomized and Hot Isostatically Pressed Consolidated |
| ASTM A 295/A295M : 2014 : REDLINE | Standard Specification for High-Carbon Anti-Friction Bearing Steel |
| ASTM B 874 : 1996 | Standard Specification for Chromium Diffusion Coating Applied by Pack Cementation Process |
| ASTM A 534 : 2017 : REDLINE | Standard Specification for Carburizing Steels for Anti-Friction Bearings |
| SAE AMS6454E | Steel, Sheet, Strip, and Plate 1.8Ni - 0.80Cr - 0.25Mo (0.38 - 0.43C) (SAE 4340) Vacuum Consumable Electrode Remelted |
| SAE AMS6559 | Steel, Bars, Wire, and Forgings 9.75 V - 5.25 Cr - 1.3 Mo (2.40 – 2.55 C) Powder Metallurgy Product Hot Isostatically Pressed |
| SAE AMS6556 | Steel, Bars, Wire, and Forgings 8V - 4Cr - 4W - 3Mo (2.45 – 2.55C) Powder Metallurgy Product Hot Isostatically Pressed |
| SAE AMS6499C | Steel, Bars, Forgings, Mechanical Tubing and Forging Stock, 2.7Si - 0.85Cr - 1.8Ni - 0.4Mo - 0.2V - (0.37 - 0.44C) Premium Aircraft Quality, Double Vacuum Melted |
| ASTM E 1951 : 2014 : REDLINE | Standard Guide for Calibrating Reticles and Light Microscope Magnifications |
| ASTM E 7 : 2017 : REDLINE | Standard Terminology Relating to Metallography |
| ASTM E 415 : 2017 : REDLINE | Standard Test Method for Analysis of Carbon and Low-Alloy Steel by Spark Atomic Emission Spectrometry |
| ASTM E 384 : 2017 : REDLINE | Standard Test Method for Microindentation Hardness of Materials |
| ASTM E 340 : 2015 : REDLINE | Standard Practice for Macroetching Metals and Alloys |
| ASTM E 350 : 2012-09 | TEST METHODS FOR CHEMICAL ANALYSIS OF CARBON STEEL, LOW-ALLOY STEEL, SILICON ELECTRICAL STEEL, INGOT IRON, AND WROUGHT IRON |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.