ASTM E 1117 : 1997 : R2006
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
Standard Practice for Design of Fuel-Alcohol Manufacturing Facilities (Withdrawn 2009)
Hardcopy , PDF
01-09-2009
English
01-02-2006
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 11.06, 2009 Applies to all FAMF as defined in Terminology E 1126, and is primarily intended for fermentation ethanol process. It applies to both (batch) continuous and FAMF systems, and describes the necessary general requirements common to all FAMF facilities.
| Committee |
E 48
|
| DocumentType |
Standard Practice
|
| Pages |
4
|
| ProductNote |
Reconfirmed 2006
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Withdrawn
|
| Supersedes |
1.1 This practice shall apply to all fuel alcohol manufacturing facilities (FAMF) as defined in Terminology E 1705. This specification is primarily intended for, but not exclusively limited to fermentation ethanol processes.
1.2 This practice applies to both batch and continuous FAMF systems. Since a wide variety of equipment configurations can exist, this engineering practice will describe the necessary general requirements common to all FAMF facilities.
1.3 This practice is to be used in conjunction with applicable local, state, and Federal codes for designing, constructing, and operating FAMF facilities.
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use . For hazard statement, see Section 11.
| ASTM E 2363 : 2014 | Standard Terminology Relating to Process Analytical Technology in the Pharmaceutical Industry |
| ASME PV CODE 8 DIV 2 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 2- ALTERNATIVE RULES |
| NFPA 85A : 1987 | PREVENTION OF FURNACE EXPLOSIONS IN FUEL OIL AND NATURAL GAS FIRED SINGLE BURNER BOILER FURNACES |
| ANSI Z21.22 : 2015 | RELIEF VALVES FOR HOT WATER SUPPLY SYSTEMS |
| ASME PV CODE 8 DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1 |
| ASME PV CODE 8 DIV 3 : 2017 | BPVC Section VIII-BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS - ALTERNATIVE RULES FOR CONSTRUCTION OF HIGH PRESSURE VESSELS |
| ASME PV CODE 4 : 2017 | BPVC Section IV-BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF HEATING BOILERS |
| ASTM E 1705 : 2015 : REDLINE | Standard Terminology Relating to Biotechnology |
| ASME PV CODE 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF POWER BOILERS |
| CFR 27(PTS1-399) : APR 2006 | ALCOHOL, TOBACCO PRODUCTS AND FIREARMS - BUREAU OF ALCOHOL, TOBACCO AND FIREARMS, DEPARTMENT OF THE TREASURY |
| ASME PV CODE 7 : 2017 | BPVC Section VII-BOILER AND PRESSURE VESSEL CODE - RECOMMENDED GUIDELINES FOR THE CARE OF POWER BOILERS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.