ASTM E 1142 : 2024
Current
Current
The latest, up-to-date edition.
Standard Terminology Relating to Thermophysical Properties
Available format(s)
Hardcopy , PDF
Language(s)
English
Published date
01-05-2024
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
E 37
|
| DocumentType |
Reference Material
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This is a compilation of only those terms and corresponding definitions included in or being considered for inclusion in ASTM documents relating to thermophysical properties. It is not intended as an all-inclusive listing of thermophysical property terms. Terms that are generally understood or defined adequately in other readily available sources are not included.
1.2A definition is a single sentence with additional information included in a Discussion.
1.3Definitions of terms specific to a particular field (such as dynamic mechanical measurements) are identified with an italicized introductory phrase.
1.4Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 967 : 2018 | Standard Test Method for Temperature Calibration of Differential Scanning Calorimeters and Differential Thermal Analyzers |
| ASTM E 2425 : 2021 | Standard Test Method for Loss Modulus Conformance of Dynamic Mechanical Analyzers |
| ASTM E 2041 : 2023 | Standard Test Method for Estimating Kinetic Parameters by Differential Scanning Calorimeter Using the Borchardt and Daniels Method |
| ASTM E 473 : 2023 : REV B | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 698 : 2023 | Standard Test Method for Kinetic Parameters for Thermally Unstable Materials Using Differential Scanning Calorimetry and the Flynn/Wall/Ozawa Method |
| ASTM E 2254 : 2024 | Standard Test Method for Storage Modulus Calibration of Dynamic Mechanical Analyzers |
| ASTM E 2509 : 2021 | Standard Test Method for Temperature Calibration of Rheometers in Isothermal Mode |
| ASTM F 2313 : 2018 | Standard Specification for Poly(glycolide) and Poly(glycolide-co-lactide) Resins for Surgical Implants with Mole Fractions Greater Than or Equal to 70 % Glycolide |
| ASTM E 2716 : 2023 | Standard Test Method for Determining Specific Heat Capacity by Modulated Temperature Differential Scanning Calorimetry |
| ASTM E 2113 : 2023 | Standard Test Method for Length Change Calibration of Thermomechanical Analyzers |
| ASTM E 793 : 2006 : R2018 | Standard Test Method for Enthalpies of Fusion and Crystallization by Differential Scanning Calorimetry |
| ASTM E 2550 : 2021 | Standard Test Method for Thermal Stability by Thermogravimetry |
| ASTM E 2602 : 2022 | Standard Test Methods for Assignment of the Glass Transition Temperature by Modulated Temperature Differential Scanning Calorimetry |
| ASTM E 3301 : 2022 | Standard Test Method for Temperature Calibration of Dynamic Mechanical Analyzers Using Thermal Lag |
| ASTM E 3142 : 2018 : REV A : R2023 | Standard Test Method for Thermal Lag of Thermal Analysis Apparatus |
| ASTM E 1953 : 2020 | Standard Practice for Description of Thermal Analysis and Rheology Apparatus |
| ASTM E 2008 : 2017 : R2021 | Standard Test Methods for Volatility Rate by Thermogravimetry |
| ASTM E 2769 : 2022 | Standard Test Method for Elastic Modulus by Thermomechanical Analysis Using Three-Point Bending and Controlled Rate of Loading |
| ASTM C 1872 : 2018 : EDT 2 | Standard Test Method for Thermogravimetric Analysis of Hydraulic Cement |
| ASTM E 2781 : 2024 | Standard Practice for Evaluation of Methods for Determination of Kinetic Parameters by Calorimetry and Differential Scanning Calorimetry |
| ASTM E 289 : 2017 | Standard Test Method for Linear Thermal Expansion of Rigid Solids with Interferometry |
| ASTM E 2510 : 2020 | Standard Test Method for Torque Calibration or Conformance of Rheometers |
| ASTM E 3070 : 2022 : EDT 1 | Standard Test Method for Shear Thinning Index of Non-Newtonian Liquids Using a Rotational Viscometer |
| ASTM E 1952 : 2023 | Standard Test Method for Thermal Conductivity and Thermal Diffusivity by Modulated Temperature Differential Scanning Calorimetry |
| ASTM E 1782 : 2022 | Standard Test Method for Determining Vapor Pressure by Thermal Analysis |
| ASTM D 3418 : 2021 | Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry |
| ASTM E 831 : 2024 | Standard Test Method for Linear Thermal Expansion of Solid Materials by Thermomechanical Analysis |
| ASTM E 2161 : 2023 : REV C | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 2071 : 2021 | Standard Practice for Calculating Heat of Vaporization or Sublimation from Vapor Pressure Data |
| ASTM E 2253 : 2021 | Standard Test Method for Temperature and Enthalpy Measurement Validation of Differential Scanning Calorimeters |
| ASTM E 2403 : 2023 | Standard Test Method for Sulfated Ash of Organic Materials by Thermogravimetry |
| ASTM E 3007 : 2021 | Standard Practice for Selection and Use of Kinetic Reference Values in the Study of Decomposition Reactions by Thermogravimetry |
| ASTM C 1470 : 2020 | Standard Guide for Testing the Thermal Properties of Advanced Ceramics |
| ASTM C 1909 : 2021 | Standard Test Method for Moisture Analysis of Plutonium Dioxide (PuO<inf>2</inf>) by Thermogravimetric Mass Spectrometry (TGA-MS) |
| ASTM F 3384 : 2021 | Standard Specification for Polydioxanone Polymer Resins for Surgical Implants |
| ASTM E 1824 : 2024 | Standard Test Method for Assignment of a Glass Transition Temperature Using Thermomechanical Analysis: Tension Method |
| ASTM E 2070 : 2023 | Standard Test Methods for Kinetic Parameters by Differential Scanning Calorimetry Using Isothermal Methods |
| ASTM E 228 : 2022 | Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer |
| ASTM E 2603 : 2015 : R2023 | Standard Practice for Calibration of Fixed-Cell Differential Scanning Calorimeters |
| ASTM E 2206 : 2021 | Standard Test Method for Force Calibration of Thermomechanical Analyzers |
| ASTM F 1925 : 2022 | Standard Specification for Semi-Crystalline Poly(lactide) Polymer and Copolymer Resins for Surgical Implants |
| ASTM E 2975 : 2023 | Standard Test Method for Calibration or Calibration Verification of Concentric Cylinder Rotational Viscometers |
| ASTM E 1131 : 2020 | Standard Test Method for Compositional Analysis by Thermogravimetry |
| ASTM E 794 : 2006 : R2018 | Standard Test Method for Melting And Crystallization Temperatures By Thermal Analysis |
| ASTM E 1640 : 2023 | Standard Test Method for Assignment of the Glass Transition Temperature By Dynamic Mechanical Analysis |
| ASTM E 3174 : 2022 | Standard Practice for Determination of Kinetic Reaction Model Using Differential Scanning Calorimetry |
| ASTM E 2890 : 2021 | Standard Test Method for Determination of Kinetic Parameters and Reaction Order for Thermally Unstable Materials by Differential Scanning Calorimetry Using the Kissinger and Farjas Methods |
| ASTM E 1641 : 2023 | Standard Test Method for Decomposition Kinetics by Thermogravimetry Using the Ozawa/Flynn/Wall Method |
| ASTM E 3116 : 2023 | Standard Test Method for Viscosity Measurement Validation of Rotational Viscometers |
| ASTM E 2160 : 2023 | Standard Test Method for Heat of Reaction of Thermally Reactive Materials by Differential Scanning Calorimetry |
| ASTM E 1867 : 2022 | Standard Test Methods for Temperature Calibration of Dynamic Mechanical Analyzers |
| ASTM E 1545 : 2022 | Standard Test Method for Assignment of the Glass Transition Temperature by Thermomechanical Analysis |
| ASTM E 2092 : 2023 | Standard Test Method for Distortion Temperature in Three-Point Bending by Thermomechanical Analysis |
| ASTM E 1356 : 2023 | Standard Test Method for Assignment of the Glass Transition Temperatures by Differential Scanning Calorimetry |
| ASTM E 1868 : 2010 : R2021 | Standard Test Methods for Loss-On-Drying by Thermogravimetry |
| ASTM E 1719 : 2024 | Standard Test Method for Vapor Pressure of Liquids by Ebulliometry |
| ASTM E 2958 : 2021 | Standard Test Methods for Kinetic Parameters by Factor Jump/Modulated Thermogravimetry |
| ASTM D 6382/D6382M : 1999 : R2022 | Standard Practice for Dynamic Mechanical Analysis and Thermogravimetry of Roofing and Waterproofing Membrane Material |
| ASTM F 2150 : 2019 | Standard Guide for Characterization and Testing of Biomaterial Scaffolds Used in Regenerative Medicine and Tissue-Engineered Medical Products |
| ASTM E 2918 : 2023 | Standard Test Method for Performance Validation of Thermomechanical Analyzers |
| ASTM E 1582 : 2021 | Standard Test Method for Temperature Calibration of Thermogravimetric Analyzers |
| ASTM E 2402 : 2019 | Standard Test Method for Mass Loss, Residue, and Temperature Measurement Validation of Thermogravimetric Analyzers |
| ASTM E 1860 : 2023 | Standard Test Method for Elapsed Time Calibration of Thermal Analyzers |
| ASTM E 2347 : 2021 | Standard Test Method for Indentation Softening Temperature by Thermomechanical Analysis |
| ASTM E 2744 : 2021 | Standard Test Method for Pressure Calibration of Thermal Analyzers |
| ASTM E 2551 : 2020 | Standard Test Methods for Humidity Calibration (or Conformation) of Humidity Generators for Use with Thermogravimetric Analyzers |
| ASTM F 3606 : 2022 | Standard Guide for Additive Manufacturing — Feedstock Materials — Testing Moisture Content in Powder Feedstock |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.