ASTM E 127 : 2015 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Practice for Fabrication and Control of Aluminum Alloy Ultrasonic Standard Reference Blocks
16-01-2021
English
01-06-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 03.03, 2017 Defines a procedure for fabricating aluminum alloy ultrasonic standard reference blocks that can be used for checking performance of ultrasonic testing equipment and for standardization and control of ultrasonic tests of aluminum alloy products using pulsed longitudinal waves introduced into test material either by the direct-contact method or by the immersion method.
| Committee |
E 07
|
| DocumentType |
Redline
|
| Pages |
19
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
1.1This practice covers a procedure for fabricating aluminum alloy ultrasonic standard reference blocks that can be used for assessing performance of ultrasonic testing equipment and for standardization and control of ultrasonic tests of aluminum alloy products using pulsed longitudinal waves introduced into test material either by the direct-contact method or by the immersion method. (1-18).2
Note 1:Practice E428 and Guide E1158 also describe procedures for selecting material, fabricating blocks, and checking response.
1.2This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM B 999 : 2015 | Standard Specification for Titanium and Titanium Alloys Plating, Electrodeposited Coatings of Titanium and Titanium Alloys on Conductive and Non-Conductive Substrate |
| I.S. EN 4050-3:2012 | AEROSPACE SERIES - TEST METHOD FOR METALLIC MATERIALS - ULTRASONIC INSPECTION OF BARS, PLATES, FORGING STOCK AND FORGINGS - PART 3: REFERENCE BLOCKS |
| PREN 4050-3 : 200P1 | AEROSPACE SERIES - TEST METHOD FOR METALLIC MATERIALS - ULTRASONIC INSPECTION OF BARS, PLATES, FORGING STOCK AND FORGINGS - REFERENCE BLOCKS |
| ASTM E 428 : 2008 : R2013 | Standard Practice for Fabrication and Control of Metal, Other than Aluminum, Reference Blocks Used in Ultrasonic Testing (Withdrawn 2019) |
| ASTM E 317 : 2016 : REDLINE | Standard Practice for Evaluating Performance Characteristics of Ultrasonic Pulse-Echo Testing Instruments and Systems without the Use of Electronic Measurement Instruments |
| SAE AMS STD 2154 : 2017-05 | INSPECTION, ULTRASONIC, WROUGHT METALS, PROCESS FOR |
| ASTM F 1512 : 1994 : R1999 | Standard Practice for Ultrasonic C-Scan Bond Evaluation of Sputtering Target-Backing Plate Assemblies |
| ASTM F 1512 : 1994 : R2003 | Standard Practice for Ultrasonic C-Scan Bond Evaluation of Sputtering Target-Backing Plate Assemblies |
| BS EN 4050-3:2012 | Aerospace series. Test method for metallic materials. Ultrasonic inspection of bars, plates, forging stock and forgings Reference blocks |
| MIL-STD-2154 Base Document:1982 | INSPECTION, ULTRASONIC, WROUGHT METALS, PROCESS FOR |
| ASTM A 21 : 1994 : R1999 | Standard Specification for Carbon Steel Axles, Non-Heat-Treated and Heat-Treated, for Railway Use (Withdrawn 2003) |
| ASTM E 428 : 2008 | Standard Practice for Fabrication and Control of Metal, Other than Aluminum, Reference Blocks Used in Ultrasonic Testing |
| ASTM E 543 : 2015 : REDLINE | Standard Specification for Agencies Performing Nondestructive Testing |
| ASME PV CODE 8 DIV 2 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 2- ALTERNATIVE RULES |
| UNI EN 4050-3 : 2013 | AEROSPACE SERIES - TEST METHOD FOR METALLIC MATERIALS - ULTRASONIC INSPECTION OF BARS, PLATES, FORGING STOCK AND FORGINGS - PART 3: REFERENCE BLOCKS |
| ASTM E 214 : 2005 | Standard Practice for Immersed Ultrasonic Testing by the Reflection Method Using Pulsed Longitudinal Waves (Withdrawn 2007) |
| ASTM A 1 : 2000 : R2010 | Standard Specification for Carbon Steel Tee Rails |
| ASTM A 1 : 2000 | Standard Specification for Carbon Steel Tee Rails |
| NASA KSC SPEC Z 0013 : 1969 | PENETRANT, MAGNETIC PARTICLE AND ULTRASONIC INSPECTION REQUIREMENTS FOR, SPECIFICATION FOR |
| NASA PRC 6510 : 2011 | PROCESS SPECIFICATION FOR ULTRASONIC INSPECTION OF WELDS |
| ASTM F 1512 : 1994 : R2011 | Standard Practice for Ultrasonic C-Scan Bond Evaluation of Sputtering Target-Backing Plate Assemblies (Withdrawn 2020) |
| MIL-STD-1875 Base Document:1983 | ULTRASONIC INSPECTION, REQUIREMENTS FOR |
| ASTM E 1158 : 2014 : REDLINE | Standard Guide for Material Selection and Fabrication of Reference Blocks for the Pulsed Longitudinal Wave Ultrasonic Testing of Metal and Metal Alloy Production Material |
| 93/711184 DC : 0 | PREN 2003-15 - AEROSPACE SERIES - ULTRASONIC TESTING REFERENCE BLOCKS |
| ISO 18175:2004 | Non-destructive testing Evaluating performance characteristics of ultrasonic pulse-echo testing systems without the use of electronic measurement instruments |
| ASTM E 1774 : 2017 : REDLINE | Standard Guide for Electromagnetic Acoustic Transducers (EMATs) |
| ASTM A 1 : 2000 : R2005 | Standard Specification for Carbon Steel Tee Rails |
| ASTM A 1 : 2000 : R2018 | Standard Specification for Carbon Steel Tee Rails |
| EN 4050-3:2012 | Aerospace series - Test method for metallic materials - Ultrasonic inspection of bars, plates, forging stock and forgings - Part 3: Reference blocks |
| ABS 0014 : 2018 | GUIDE FOR NONDESTRUCTIVE INSPECTION OF HULL WELDS |
| ASTM E 2375 : 2016 : REDLINE | Standard Practice for Ultrasonic Testing of Wrought Products |
| SAE AMS2632A | Inspection, Ultrasonic, of Thin Materials 0.50 Inch (12.7 mm) and Under in Cross-Sectional Thickness |
| ASTM E 1001 : 2016 : REDLINE | Standard Practice for Detection and Evaluation of Discontinuities by the Immersed Pulse-Echo Ultrasonic Method Using Longitudinal Waves |
| ASTM E 1158 : 2014 : REDLINE | Standard Guide for Material Selection and Fabrication of Reference Blocks for the Pulsed Longitudinal Wave Ultrasonic Testing of Metal and Metal Alloy Production Material |
| ASTM E 1324 : 2016 : REDLINE | Standard Guide for Measuring Some Electronic Characteristics of Ultrasonic Testing Instruments |
| ASTM E 2375 : 2016 : REDLINE | Standard Practice for Ultrasonic Testing of Wrought Products |
| ASTM E 317 : 2016 : REDLINE | Standard Practice for Evaluating Performance Characteristics of Ultrasonic Pulse-Echo Testing Instruments and Systems without the Use of Electronic Measurement Instruments |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.