• Shopping Cart
    There are no items in your cart

ASTM E 1320 : 2015 : REDLINE

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Reference Radiographs for Titanium Castings

Available format(s)

PDF

Superseded date

25-06-2020

Language(s)

English

Published date

01-09-2015

€59.22
Excluding VAT

CONTAINED IN VOL. 03.03, 2017 Describes the categories and severity levels of discontinuities in titanium castings that may be revealed by radiographic examination.

Committee
E 07
DocumentType
Redline
Pages
4
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

1.1The reference radiographs provided in the adjunct to this standard are reproductions of original radiographs and are supplied as a means for establishing some of the categories and severity levels of discontinuities in titanium castings that may be revealed by radiographic examination. Use of this standard for the specification or grading of castings requires procurement of the adjunct reference radiographs which illustrate the discontinuity types and severity levels. They should be used in accordance with contractual specifications.

Note 1:The original radiographs produced for Volume I were taken with X-rays in the range of 110 KV to 220 KV. The original radiographs produced for Volume II were taken with X-rays in the range of 200 K to 340 KV.

1.2These film reference radiographs are not intended to illustrate the types and degrees of discontinuities found in titanium castings when performing digital radiography. If performing digital radiography of titanium castings, refer to Digital Reference Image Standard E2669.

1.3These reference radiographs consist of two volumes. Volume I, described in Table 1, is applicable to a wall thickness of up to 1 in. (0 to 25.4 mm). Volume II, described in Table 2, is applicable to a wall thickness of over 1 in. to 2 in. (25.4 mm to 50.8 mm). The standard may be used, where there is no other applicable standard, for other thicknesses for which agreement has been reached between purchaser and manufacturer.

Note 1:1 in. = 25.4 mm.

Note 1:1 in. = 25.4 mm.

Note 2:The reference radiographs are not impacted by this revision. There have been no revisions to the adjunct reference radiographs since original issue. The adjunct reference radiographs of any issue remain valid and may be used to this standard.

1.4The plates produced to serve for use in this standard were purposely cast to exhibit the desired discontinuity. The plates were cast using different processes as shown in Table 1 and Table 2. Hot isostatic pressing was not used on any of the plates.

1.5From time to time, there may be minor changes to the process for manufacturing of the reference radiograph adjunct materials. These changes could include changes in the films or processing chemicals used, changes in the dies or printing for the cardboard mats, etc.; however, in all cases, these changes are reviewed by the Illustration Monitoring Subcommittee and all reference radiographs are reviewed against a fixed prototype image to ensure that there are no changes to the acceptance level represented by the reference radiographs. Therefore, the adjunct reference radiographs remain valid for use with this standard regardless of the date of production or the revision level of the text standard.

1.6The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SAE AMS 4962 : 2016 TITANIUM ALLOY, INVESTMENT CASTINGS, 6 AL - 4 V HOT ISOSTATICALLY PRESSED
SAE AMS 4992 : 2014 CASTING, STRUCTURAL INVESTMENT, TITANIUM ALLOY 6AL - 4V HOT ISOSTATICALLY PRESSED
DIN EN 2002-21:2000-07 (Draft) AEROSPACE SERIES - METALLIC MATERIALS; TEST METHODS - PART 21: RADIOGRAPHIC TESTING OF CASTINGS
99/710246 DC : JUL 99 PREN 2002-21 - AEROSPACE SERIES - METALLIC MATERIALS - TEST METHODS - PART 21: RADIOGRAPHIC TESTING OF CASTINGS
I.S. EN 12681-1:2017 FOUNDING - RADIOGRAPHIC TESTING - PART 1: FILM TECHNIQUES
NF EN 16866 : 2017 METALLIC AND OTHER INORGANIC COATINGS - SIMULTANEOUS THICKNESS AND ELECTRODE POTENTIAL DETERMINATION OF INDIVIDUAL LAYERS IN MULTILAYER NICKEL DEPOSITS (STEP TEST)
ASTM E 1030/E1030M : 2015 : REDLINE Standard Practice for Radiographic Examination of Metallic Castings
ASTM E 1030 : 2005 Standard Test Method for Radiographic Examination of Metallic Castings
EN 12681-1:2017 Founding - Radiographic testing - Part 1: Film techniques
EN 12681:2003 Founding - Radiographic examination
ASTM E 1030 : 2005 : R2011 Standard Test Method for Radiographic Examination of Metallic Castings
ASTM E 2736 : 2017 : REDLINE Standard Guide for Digital Detector Array Radiography
NBR 15892 : 2016 ORTHOPEDIC IMPLANTS - NON-DESTRUCTIVE TESTING - GUIDELINES AND REQUIREMENTS FOR RADIOGRAPHIC PROCEDURES AND INSPECTION OF METALLIC COMPONENTS
UNI EN 4800-008 : 2011 AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 008: PRE-PRODUCTION AND PRODUCTION CASTINGS
SAE AMS 4985 : 2014 TITANIUM ALLOY, INVESTMENT CASTINGS 6AL - 4V 130 UTS, 120 YS, 6% EL HOT ISOSTATICALLY PRESSED ANNEAL OPTIONAL OR WHEN SPECIFIED
BS EN 12681-1:2017 Founding. Radiographic testing Film techniques
DIN EN 12681:2003-06 FOUNDING - RADIOGRAPHIC EXAMINATION
NF EN 4800-008 : 2012 AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 008: PRE-PRODUCTION AND PRODUCTION CASTINGS
I.S. EN 12681:2003 FOUNDING - RADIOGRAPHIC EXAMINATION
SAE AMS 2175 : 2010 CASTINGS, CLASSIFICATION AND INSPECTION OF
I.S. EN 4800-008:2010 AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 008: PRE-PRODUCTION AND PRODUCTION CASTINGS
PREN 4800-008 : 200P2 AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 8: PRE-PRODUCTION AND PRODUCTION CASTINGS
PREN 2002-21 : 200P2 AEROSPACE SERIES - METALLIC MATERIALS - TEST METHODS - PART 21: RADIOGRAPHIC TESTING OF CASTINGS
BS EN 12681:2003 Founding. Radiographic examination
EN 4800-008:2010 Aerospace series - Titanium and titanium alloys - Technical specification - Part 008: Pre-production and production castings
BS EN 4800-008:2010 Aerospace series. Titanium and titanium alloys. Technical specification Pre-production and production castings
ASTM F 629 : 2015 : REDLINE Standard Practice for Radiography of Cast Metallic Surgical Implants
SAE AMS 4991 : 2014 TITANIUM ALLOY CASTINGS, INVESTMENT 6AL - 4V HOT ISOSTATIC PRESSED, ANNEAL OPTIONAL

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.