ASTM E 222 : 2023
Current
The latest, up-to-date edition.
Standard Test Methods for Hydroxyl Groups Using Acetic Anhydride Acetylation
Hardcopy , PDF
English
08-06-2023
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
D 16
|
| DocumentType |
Test Method
|
| Pages |
9
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1These test methods cover the determination of hydroxyl groups attached to primary and secondary carbon atoms in aliphatic and alicyclic compounds and phenols.
1.2Three test methods are given as follows:
|
| Sections |
| Test Method A (Pressure Bottle Method) | 8 – 14 |
| Test Method B (Reflux Method) | 16 – 22 |
| Test Method C (Perchloric Acid Catalyzed Method) | 24 – 30 |
1.2.1Test Method A is recommended for general use. Test Method B is included to give a standard procedure for the method that has been used widely. Test Method C is recommended when the results are required in a minimum period of time or where ambient temperature for the reaction is desired.
1.2.2The results obtained using Test Methods A and B will be essentially the same, but the results obtained using Test Method C will be higher (up to approximately 4 % relative) than those obtained using the other two methods.
1.2.3Statements on precision are included with each test method. The precision of Test Methods A and C is consistent over a wide range of hydroxyl content (tested over hydroxyl number range of 250 to 1600), whereas Test Method B is less precise at the higher hydroxyl content level than it is at the lower hydroxyl content level. In general, Test Method A is approximately two-fold as precise as Test Method C. Test Method B has approximately the same precision as Test Method C at the lower hydroxyl content level but poorer precision at the higher hydroxyl content level.
1.2.4The interferences are essentially the same for the three methods. Some compounds can be analyzed using Test Methods A or B but not using Test Method C because of interfering reactions of the strong acid catalyst with the compound being analyzed or the acetate product formed in the determination. However, because of its increased reactivity, Test Method C is applicable for determination of some compounds, particularly sterically hindered secondary alcohols, which react too slowly or not at all in Test Methods A and B.
Note 1:Other methods for determination of hydroxyl groups are given in Test Methods D1957, D2195, E326, E335, and E567.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4In determining the conformance of the test results using this method to applicable specifications, results shall be rounded in accordance with the rounding off methods of Practice E29.
1.5Review the current appropriate Safety Data Sheets (SDS) for detailed information concerning toxicity, first aid procedures, and safety precautions.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section 7.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 1899 : 2016 | Standard Test Method for Hydroxyl Groups Using Reaction with <emph type="ital">p</emph >-Toluenesulfonyl Isocyanate (TSI) and Potentiometric Titration with Tetrabutylammonium Hydroxide |
| ASTM E 1547 : 2009 : R2023 | Standard Terminology Relating to Industrial and Specialty Chemicals |
| ASTM D 6342 : 2022 | Standard Practice for Polyurethane Raw Materials: Determining Hydroxyl Number of Polyols by Near Infrared (NIR) Spectroscopy |
| ASTM D 4274 : 2023 | Standard Test Methods for Testing Polyurethane Raw Materials: Determination of Hydroxyl Numbers of Polyols |
| SAE AMS3021G | Fluid, Reference for Testing Di-Ester (Polyol) Resistant Material |
| ASTM D 1193 : 2024 | Standard Specification for Reagent Water |
| ASTM E 203 : 2023 | Standard Test Method for Water Using Volumetric Karl Fischer Titration |
| ASTM D 6809 : 2020 : REV A | Standard Guide for Quality Control and Quality Assurance Procedures for Aromatic Hydrocarbons and Related Materials |
| ASTM E 200 : 2016 | Standard Practice for Preparation, Standardization, and Storage of Standard and Reagent Solutions for Chemical Analysis |
| ASTM E 200 : 2023 | Standard Practice for Preparation, Standardization, and Storage of Standard and Reagent Solutions for Chemical Analysis |
| ASTM D 6809 : 2024 | Standard Guide for Quality Control and Quality Assurance Procedures for Aromatic Hydrocarbons and Related Materials |
| ASTM D 1193 : 2006 : R2018 | Standard Specification for Reagent Water |
| ASTM E 203 : 2024 | Standard Test Method for Water Using Volumetric Karl Fischer Titration |
| ASTM E 203 : 2016 | Standard Test Method for Water Using Volumetric Karl Fischer Titration |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.