ASTM E 227 : 1990 : R1996
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
Standard Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane Technique (Withdrawn 2002)
Hardcopy , PDF
05-11-2013
English
31-12-2010
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL 03.05, 2001 Deals with spectrometric analysis of aluminum and aluminum alloys for elements in the concentration ranges listed. Applies mainly to control analysis of chill-cast samples. Other forms can be analyzed given that they are adequately massive to prevent undue heating, they allow machining flat surfaces with minimum dimension of around 1.6 in. (16 mm) and reference materials of similar metallurgical condition and chemical composition are obtainable.
| Committee |
E 01
|
| DocumentType |
Test Method
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Withdrawn
|
1.1 This test method covers the spectrometric analysis of aluminum and aluminum alloys for the following elements in the concentration ranges indicated:
Concentration Element Range, % Copper 0.001 to 30.0 Silicon 0.001 to 14.0 Magnesium 0.001 to 11.0 Zinc 0.001 to 10.0 Nickel 0.001 to 10.0 Manganese 0.001 to 8.0 Tin 0.001 to 7.5 Silver 0.001 to 5.0 Iron 0.001 to 4.0 Chromium 0.001 to 4.0 Cadmium 0.001 to 2.0 Cobalt 0.001 to 2.0 Beryllium 0.001 to 1.2 Zirconium 0.001 to 1.0 Lead 0.002 to 0.7 Bismuth 0.001 to 0.7 Titanium 0.001 to 0.5 Calcium 0.001 to 0.2 Barium 0.001 to 0.05 Boron 0.001 to 0.05 Gallium 0.001 to 0.05 Sodium 0.001 to 0.05 Vanadium 0.001 to 0.051.2 The test method is applicable primarily to the control analysis of chill-cast samples. Other forms may be analyzed, provided that ( ) they are sufficiently massive to prevent undue heating, ( ) they permit machining flat surfaces having a minimum dimension of approximately 16 mm (1.6 in.), and ( ) reference materials of similar metallurgical condition and chemical composition are available.
1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| SAE AMS4280J | Aluminum Alloy Castings, Permanent Mold 5.0Si - 1.2Cu - 0.5Mg (355.0-T71) Solution Heat Treated and Overaged |
| ASTM A 676 : 72(1980) | SPECIFICATION FOR HOT-DIPPED ALUMINUM COATINGS ON FERROUS ARTICLES |
| MIL-DTL-45225 Revision F:1998 | ALUMINUM ALLOY ARMOR, FORGED |
| ASTM B 531 : 1990 : R1998 : EDT 1 | Standard Specification for Aluminum-Alloy 5005 Drawing Stock for Electrical Purposes (Withdrawn 2003) |
| MIL-DTL-46192 Revision C:1998 | ALUMINUM ALLOY ARMOR ROLLED PLATE (1/2 TO 4 INCHES THICK), WELDABLE (ALLOY 2519) |
| MIL-DTL-46063 Revision H:1998 | ARMOR PLATE, ALUMINUM ALLOY, 7039 |
| QQ-A-225 Revision G:1990 | ALUMINUM AND ALUMINUM ALLOY BAR, ROD, WIRE, OR SPECIAL SHAPES, ROLLED, DRAWN, OR COLD FINISHED, GENERAL SPECIFICATION FOR |
| MIL A 46192 : B | ALUMINUM ALLOY ARMOR ROLLED PLATE (1/2 TO 4 INCHES THICK), WELDABLE (ALLOY 2519) |
| SAE AMS4210K | Aluminum Alloy, Castings 5.0Si - 1.2Cu - 0.50Mg (355.0-T51) Precipitation Heat Treated |
| MIL-DTL-46083 Revision D:1998 | ALUMINUM ALLOY ARMOR, EXTRUDED, WELDABLE |
| ASTM B 736 : 2000 : R2006 | Standard Specification for Aluminum, Aluminum Alloy and Aluminum-Clad Steel Cable Shielding Stock (Withdrawn 2015) |
| SAE AMS4223E | Aluminum Alloy, Castings 4.5Cu - 0.70Ag - 0.30Mn - 0.25Mg - 0.25Ti (A201.0-T4) Solution Heat Treated and Naturally Aged |
| SAE AMS4281G | Aluminum Alloy Castings, Permanent Mold 5.0Si - 1.2Cu - 0.50Mg (355.0-T6) Solution and Precipitation Heat Treated |
| ASTM F 468M:2006 | Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use [Metric] |
| ASTM B 233 : 1997 : R2012 | Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes |
| SAE AMSA21180C | Aluminum-Alloy Castings, High Strength |
| SAE AMS4235C | Aluminum Alloy Castings 4.6Cu - 0.35Mn - 0.25Mg - 0.22Ti (A206.0-T7) Solution and Precipitation Heat Treated |
| ASTM B 736 : 2000 | Standard Specification for Aluminum, Aluminum Alloy and Aluminum-Clad Steel Cable Shielding Stock |
| ASTM F 901 : 2001 : R2012 | Standard Specification for Aluminum Transmission Tower Bolts and Nuts |
| ASTM F 467M : 2006 : REV A : EDT 2 | Standard Specification for Nonferrous Nuts for General Use (Metric) |
| ASTM B 85 : 2003 | Standard Specification for Aluminum-Alloy Die Castings |
| ASTM F 467M : 2006 : REV A : EDT 1 | Standard Specification for Nonferrous Nuts for General Use [Metric] |
| ASTM F 467M : 2006 : REV A : R2018 | Standard Specification for Nonferrous Nuts for General Use (Metric) |
| ASTM F 468 : 2016 | Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use |
| ASTM F 468M : 2006 : R2018 | Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use (Metric) |
| ASTM F 901 : 2020 | Standard Specification for Aluminum Transmission Tower Bolts and Nuts |
| ASTM F 467 : 2013 : R2018 | Standard Specification for Nonferrous Nuts for General Use |
| ASTM F 901 : 2001 | Standard Specification for Aluminum Transmission Tower Bolts and Nuts |
| SAE AMS4214J | Castings, Aluminum Alloy Sand 5.0Si - 1.2Cu - 0.50Mg (355.0-T71) Solution Heat Treated and Overaged |
| ASTM F 468M : 2006 : R2012 | Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use (Metric) |
| ASTM F 467M : 2006 : REV A : R2012 | Standard Specification for Nonferrous Nuts for General Use (Metric) |
| ASTM B 404/B404M : 2002 | Standard Specification for Aluminum and Aluminum-Alloy Seamless Condenser and Heat-Exchanger Tubes with Integral Fins (Withdrawn 2006) |
| MIL-DTL-46118 Revision E:1998 | ALUMINUM ALLOY ARMOR, 2219, ROLLED PLATE AND DIE FORGED SHAPES |
| ASTM B 233 : 1997 : R2003 : EDT 1 | Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes |
| ASTM E 607 : 2002 | Standard Test Method for Atomic Emission Spectrometric Analysis Aluminum Alloys by the Point to Plane Technique Nitrogen Atmosphere |
| ASTM F 901 : 2001 : R2007 | Standard Specification for Aluminum Transmission Tower Bolts and Nuts |
| ASTM B 233 : 1997 : R2007 | Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes |
| SAE AMS4215H | Aluminum Alloy, Castings 5.0Si - 1.2Cu - 0.50Mg (C355.0-T6) Solution and Precipitation Heat Treated |
| SAE AMSQQA225C | Aluminum and Aluminum Alloy, Bar, Rod, Wire, or Special Shapes; Rolled, Drawn, or Cold Finished; General Specification For |
| ASTM F 468M : 2006 : EDT 1 | Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use [Metric] |
| ASTM F 901 : 2001 : R2017 | Standard Specification for Aluminum Transmission Tower Bolts and Nuts |
| ASTM B 313M : 1988 | Specification for Aluminum and Aluminum-Alloy Round Welded Tubes (Metric) (Withdrawn 1990) |
| SAE AMS4288 | Aluminum Alloy Castings 7.0Si - 0.58Mg - 0.15Ti (E357.0-T6) Solution and Precipitation Heat Treated |
| AWS C2.25/C2.25M : 2012 | SPECIFICATION FOR THERMAL SPRAY FEEDSTOCK - WIRE AND RODS |
| AWS A5.10 : 1992 | BARE ALUMINUM AND ALUMINUM ALLOY WELDING ELECTRODES AND RODS, SPECIFICATION FOR |
| AWS A5.3 : 1991 | SPECIFICATION FOR ALUMINUM AND ALUMINUM ALLOY ELECTRODES FOR SHIELDED METAL ARC WELDING |
| SAE AMS4242C | Aluminum Alloy, Castings 4.7Cu - 0.60Ag - 0.35Mn - 0.25Mg - 0.25Ti (B201.0-T7) Solution Heat Treated and Overaged |
| ASTM B 308M : 1988 | Specification for Aluminum-Alloy 6061-T6 Standard Structural Shapes, Rolled or Extruded (Metric) (Withdrawn 1990) |
| ASTM B 233 : 1997 : R2016 | Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes |
| ASTM B 233 : 1997 | Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes |
| ASTM E 607 : 2002 | Standard Test Method for Atomic Emission Spectrometric Analysis Aluminum Alloys by the Point to Plane Technique Nitrogen Atmosphere |
| ASTM E 716 : 2016 : REDLINE | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry |
| ASTM E 305 : 2013 : REDLINE | Standard Practice for Establishing and Controlling Atomic Emission Spectrochemical Analytical Curves |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.