ASTM E 2357 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Determining Air Leakage Rate of Air Barrier Assemblies
Hardcopy , PDF
18-10-2023
English
14-11-2018
Important note : Users cannot be edited or removed once added to your Multi user PDF.This test method covers the determination of the air leakage rate of air barrier assemblies that are used in building enclosures.
| Committee |
E 06
|
| DocumentType |
Test Method
|
| Pages |
11
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the determination of the air leakage rate of air barrier assemblies that are used in building enclosures. This procedure measures the air leakage of a representative air barrier assembly before and after exposure to specific conditioning cycles and then assigns a rating dependent upon the results. Although this is a laboratory procedure, the method may also be applied to site mockups.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 7586/D7586M : 2011 | Standard Test Method for Quantification of Air Intrusion in Low-Sloped Mechanically Attached Membrane Roof Assemblies (Withdrawn 2020) |
| ASTM D 8052/D8052M : 2017 | Standard Test Method for Quantification of Air Leakage in Low-Sloped Membrane Roof Assemblies |
| ASTM D 8052/D8052M : 2022 | Standard Test Method for Quantification of Air Leakage in Low-Sloped Membrane Roof Assemblies |
| ASTM E 2112 : 2023 | Standard Practice for Installation of Exterior Windows, Doors and Skylights |
| ASTM E 3054/E3054M : 2023 | Standard Guide for Characterization and Use of Hygrothermal Models for Moisture Control Design in Building Envelopes |
| ASTM E 2813 : 2018 | Standard Practice for Building Enclosure Commissioning |
| ASTM E 3054/E3054M : 2016 | Standard Guide for Characterization and Use of Hygrothermal Models for Moisture Control Design in Building Envelopes |
| ASTM E 1677 : 2019 | Standard Specification for Air Barrier (AB) Material or Assemblies for Low-Rise Framed Building Walls |
| ASTM E 2178 : 2003 | Standard Test Method for Air Permeance of Building Materials |
| ASTM E 1677 : 1995 : R2000 | Standard Specification for an Air Retarder (AR) Material or System for Low-Rise Framed Building Walls |
| ASTM E 1424 : 1991 : R2008 | Standard Test Method for Determining the Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure and Temperature Differences Across the Specimen |
| ASTM E 1677 : 2011 | Standard Specification for Air Barrier (AB) Material or System for Low-Rise Framed Building Walls |
| ASTM E 2178 : 2013 | Standard Test Method for Air Permeance of Building Materials |
| ASTM E 1424 : 2022 | Standard Test Method for Determining the Rate of Air Leakage Through Exterior Windows, Skylights, Curtain Walls, and Doors Under Specified Pressure and Temperature Differences Across the Specimen |
| ASTM E 1424 : 1991 : R2000 | Standard Test Method for Determining the Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure and Temperature Differences Across the Specimen |
| ASTM E 2178 : 2021 : REV A | Standard Test Method for Determining Air Leakage Rate and Calculation of Air Permeance of Building Materials |
| ASTM E 330/E330M : 2014 : R2021 | Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference |
| ASTM E 1677 : 2023 | Standard Specification for Air Barrier (AB) Material or Assemblies for Low-Rise Framed Building Walls |
| ASTM E 1677 : 2005 | Standard Specification for an Air Retarder (AR) Material or System for Low-Rise Framed Building Walls |
| ASTM E 2178 : 2021 | Standard Test Method for Determining Air Leakage Rate and Calculation of Air Permeance of Building Materials |
| ASTM E 2178 : 2011 | Standard Test Method for Air Permeance of Building Materials |
| ASTM E 2178 : 2001 | Standard Test Method for Air Permeance of Building Materials |
| ASTM E 1424 : 1991 : R2016 | Standard Test Method for Determining the Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure and Temperature Differences Across the Specimen |
| ASTM E 330/E330M : 2014 | Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.