![header thumbnail](/images/publishers\astm_cover.gif)
ASTM E 2580 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Practice for Ultrasonic Testing of Flat Panel Composites and Sandwich Core Materials Used in Aerospace Applications
Hardcopy , PDF
02-03-2024
English
22-12-2017
Committee |
E 07
|
DocumentType |
Standard Practice
|
Pages |
7
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This practice establishes two procedures for ultrasonic testing (UT) of flat panel composites and flat sandwich core panels (parallel surfaces). Typical as-fabricated lay-ups include uniaxial, cross ply and angle ply laminates; as well as honeycomb sandwich core materials. These procedures can be used throughout the life cycle of the materials; product and process design optimization, on line process control, after manufacture inspection, and in service inspection. Contact methods such as angle-beam techniques using shear waves, or surface-beam techniques using Lamb waves, are not discussed.
1.2Ultrasonic testing is a common subsurface method for detection of laminar oriented discontinuities. Two techniques can be considered based on panel surface accessibility; pulse echo for one sided and through transmission (bubblers/squirters) for two sided. As used in this practice, both require the use of a pulsed straight-beam ultrasonic longitudinal wave followed by observing indications of either the reflected (pulse-echo) or received (through transmission) wave. The general types of anomalies detected by both techniques include foreign materials, delamination, disbond/un-bond, fiber de-bonding, inclusions, porosity, and voids.
1.3This practice provides two ultrasonic test procedures. Each has its own merits and requirements for inspection and shall be selected as agreed upon in a contractual document.
1.3.1Test Procedure A, Pulse Echo (non-contacting and contacting), is at a minimum a single transducer transmitting and receiving a longitudinal wave in the range of 0.5 to 20 MHz (see Fig. 1). This procedure requires access to only one side of the specimen. This procedure can be conducted by automated or manual means. Automated and manual test results may be imaged or recorded.
FIG. 1Test Procedure A, Pulse Echo Apparatus Set-up
![Test Procedure A, Pulse Echo Apparatus Set-up](http://www.astm.org/HTTP/IMAGES/E2580_006028.png)
1.3.2Test Procedure B, Through Transmission, is a combination of two transducers. One transmits a longitudinal wave and the other receives the longitudinal wave in the range of 0.5 MHz to 20 MHz (see Fig. 2). This procedure requires access to both sides of the specimen. This procedure is automated and the examination results are recorded.
FIG. 2Test Procedure B, Through Transmission Apparatus Set-up
![Test Procedure B, Through Transmission Apparatus Set-up](http://www.astm.org/HTTP/IMAGES/E2580_104138.png)
1.4This practice does not specify accept-reject criteria.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM E 2981 : 2015 : EDT 1 | Standard Guide for Nondestructive Testing of the Composite Overwraps in Filament Wound Pressure Vessels Used in Aerospace Applications |
ASTM E 543 : 2015 | Standard Specification for Agencies Performing Nondestructive Testing |
ASTM E 2981 : 2021 | Standard Guide for Nondestructive Examination of Composite Overwraps in Filament Wound Pressure Vessels Used in Aerospace Applications |
ASTM E 3370 : 2023 | Standard Practice for Matrix Array Ultrasonic Testing of Composites, Sandwich Core Constructions, and Metals |
ASTM E 2533 : 2021 | Standard Guide for Nondestructive Examination of Polymer Matrix Composites Used in Aerospace Applications |
ASTM E 1316 : 2022 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2011 : REV B | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2015 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2009 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2008 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2010 : REV C | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2020 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2017 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2013 : REV C | Standard Terminology for Nondestructive Examinations |
ASTM D 3878 : 2002 : REV A | Standard Terminology for Composite Materials |
ASTM E 1316 : 2000 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM D 3878 : 2023 | Standard Terminology for Composite Materials |
ASTM E 543 : 2021 | Standard Specification for Agencies Performing Nondestructive Testing |
ASTM E 1316 : 2019 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM D 3878 : 2015 | Standard Terminology for Composite Materials |
ASTM E 1434 : 2000 : R2013 | Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases (Withdrawn 2015) |
ASTM D 3878 : 2019 | Standard Terminology for Composite Materials |
ASTM D 3878 : 2000 | Standard Terminology Composite Materials |
ASTM E 1316 : 2014 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2013 : REV B | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2018 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2011 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2007 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2015 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2019 : REV B | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2021 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2013 : REV D | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2000 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2019 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2001 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2003 | Standard Terminology for Nondestructive Examinations |
ASTM E 1471 : 1992 : R2008 | Standard Guide for Identification of Fibers, Fillers, and Core Materials in Computerized Material Property Databases |
ASTM D 3878 : 2003 : REV A | Standard Terminology for Composite Materials |
ASTM E 1316 : 2018 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM D 3878 : 2016 | Standard Terminology for Composite Materials |
ASTM E 1309 : 2000 | Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases |
ASTM E 1471 : 1992 : R1998 | Standard Guide for Identification of Fibers, Fillers, and Core Materials in Computerized Material Property Databases |
ASTM E 1316 : 2024 | Standard Terminology for <?Pub Dtl?>Nondestructive Examinations |
ASTM D 3878 : 2019 : REV A | Standard Terminology for Composite Materials |
ASTM D 3878 : 2020 : REV A | Standard Terminology for Composite Materials |
ASTM D 3878 : 1998 | Standard Terminology Composite Materials |
ASTM E 1316 : 2006 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2016 | Standard Terminology for Nondestructive Examinations |
ASTM D 3878 : 2018 | Standard Terminology for Composite Materials |
ASTM E 1316 : 2021 : REV D | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2002 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1434 : 2000 | Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases |
ASTM E 1316 : 2014 : EDT 1 | Standard Terminology for Nondestructive Examinations |
ASTM D 3878 : 2002 | Standard Terminology for Composite Materials |
ASTM D 3878 : 2020 : REV B | Standard Terminology for Composite Materials |
ASTM E 1316 : 2010 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1471 : 1992 : R2014 | Standard Guide for Identification of Fibers, Fillers, and Core Materials in Computerized Material Property Databases (Withdrawn 2015) |
ASTM E 1316 : 2022 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2013 | Standard Terminology for Nondestructive Examinations |
ASTM D 3878 : 2004 | Standard Terminology for Composite Materials |
ASTM E 1316 : 2021 : REV B | Standard Terminology for Nondestructive Examinations |
ASTM D 3878 : 2007 : R2013 | Standard Terminology for Composite Materials |
ASTM E 1309 : 2000 : R2011 | Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases (Withdrawn 2015) |
ASTM D 3878 : 2020 : REDLINE | Standard Terminology for Composite Materials |
ASTM E 1316 : 2017 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM D 3878 : 2020 | Standard Terminology for Composite Materials |
ASTM E 1471 : 1992 : R2004 | Standard Guide for Identification of Fibers, Fillers, and Core Materials in Computerized Material Property Databases |
ASTM D 3878 : 2003 | Standard Terminology for Composite Materials |
ASTM E 1316 : 2016 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2009 | Standard Terminology for Nondestructive Examinations |
ASTM D 3878 : 2007 | Standard Terminology for Composite Materials |
ASTM E 1316 : 2002 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2004 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2007 : REV C | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2010 : REV B | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2013 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2023 : REV A | Standard Terminology for Nondestructive Examinations |
ASTM E 1309 : 2000 : R2005 | Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases |
ASTM D 3878 : 2004 : REV A | Standard Terminology for Composite Materials |
ASTM E 1316 : 2021 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2007 : REV B | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2005 | Standard Terminology for Nondestructive Testing |
ASTM E 1316 : 2004 | Standard Terminology for Nondestructive Examinations |
ASTM E 1434 : 2000 : R2006 | Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases |
ASTM E 1316 : 2021 : REV C | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2007 | Standard Terminology for Nondestructive Examinations |
ASTM D 3878 : 2001 | Standard Terminology Composite Materials |
ASTM E 1316 : 2023 | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2023 : REV B | Standard Terminology for Nondestructive Examinations |
ASTM E 1316 : 2012 | Standard Terminology for Nondestructive Examinations |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.