ASTM E 287 : 2002 : R2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Laboratory Glass Graduated Burets
Hardcopy , PDF
20-11-2024
English
01-07-2019
Important note : Users cannot be edited or removed once added to your Multi user PDF.
This specification covers requirements for glass burets of precision and general-purpose grades suitable for laboratory use.
| Committee |
E 41
|
| DocumentType |
Standard
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers requirements for glass burets of precision and general-purpose grades suitable for laboratory use.
1.1.1Class A—Each buret of precision grade may be marked with the letter “A” to signify compliance with applicable construction and accuracy requirements in Table 1 and Table 2. Each buret may be marked with a permanent serial number at the option of the manufacturer.
1.1.2Class B—General purpose burets are of the same basic design as Class A burets. However, volumetric tolerances for Class B burets shall be within twice the specified range allowed for Class A burets. These burets need not be marked with their class designation or serial number. See Table 1 and Table 3 for tolerances and dimensional requirements.
Note 1:The Twelfth General (International) Conference on Weights and Measures redefined the litre as a “special name for the cubic decimetre,” but agreed to permit continuance of the terms litre, millilitre, and mL, except in association with measurements of the highest precision. For volumetric glassware the difference between the old and new meanings of litre is negligible. Therefore, either mL or cm3 may be marked on ware covered by this standard.
1.1.3Product with a stated capacity not listed in this standard may be specified Class A Tolerance when product conforms to the tolerance range of the next smaller volumetric standard product listed in Table 1.
1.2This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 776 : 2023 | Standard Test Method for Determination of Forms of Chlorine in Refuse-Derived Fuel |
| ASTM E 50 : 2024 | Standard Practices for Apparatus, Reagents, and Safety Considerations for Chemical Analysis of Metals, Ores, and Related Materials |
| ASTM D 6647 : 2018 : R2024 | Standard Test Method for Determination of Acid Soluble Iron via Atomic Absorption |
| ASTM D 4607 : 2014 : R2021 | Standard Test Method for Determination of Iodine Number of Activated Carbon |
| ASTM D 632 : 2012 : R2020 : EDT 1 | Standard Specification for Sodium Chloride |
| ASTM E 694 : 2018 : R2024 | Standard Specification for Laboratory Glass Volumetric Apparatus |
| ASTM E 911 : 1998 : R2021 | Standard Specification for Glass Stopcocks with Polytetrafluoroethylene (PTFE) Plugs |
| ASTM D 664 : 2018 : EDT 2 | Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration |
| ASTM D 664 : 2017 : REV A | Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration |
| ASTM E 1157 : 1987 : R2006 | Standard Specification for Sampling and Testing of Reusable Laboratory Glassware |
| ASTM E 1133 : 1986 : R2010 | Standard Practice for Performance Testing of Packaged Laboratory Apparatus for United States Government Procurements |
| ASTM E 1133 : 1986 : R2000 | Standard Practice for Performance Testing of Packaged Laboratory Apparatus for United States Government Procurements |
| ASTM E 1157 : 1987 : R2018 : EDT 1 | Standard Specification for Sampling and Testing of Reusable Laboratory Glassware |
| ASTM E 1157 : 1987 : R1996 | Standard Specification for Sampling and Testing of Reusable Laboratory Glassware |
| ASTM D 664 : 2024 | Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration |
| ASTM E 675 : 1994 : R1998 | Standard Specification for Interchangeable Taper-Ground Stopcocks And Stoppers |
| ASTM E 911 : 1998 : R2015 | Standard Specification for Glass Stopcocks with Polytetrafluoroethylene (PTFE) Plugs |
| ASTM E 1157 : 1987 : R2011 | Standard Specification for Sampling and Testing of Reusable Laboratory Glassware |
| ASTM E 921 : 1997 : R2022 | Standard Specification for Export Packaged Laboratory Apparatus |
| ASTM E 1133 : 1986 : R2005 | Standard Practice for Performance Testing of Packaged Laboratory Apparatus for United States Government Procurements |
| ASTM E 1133 : 1986 : R2022 | Standard Practice for Performance Testing of Packaged Laboratory Apparatus for United States Government Procurements |
| ASTM D 664 : 1995 | Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration |
| ASTM E 1133 : 1986 : R1996 : EDT 1 | Standard Practice for Performance Testing of Packaged Laboratory Apparatus for United States Government Procurements |
| ASTM E 921 : 1997 : R2016 | Standard Specification for Export Packaged Laboratory Apparatus |
| ASTM E 1133 : 1986 : R2016 | Standard Practice for Performance Testing of Packaged Laboratory Apparatus for United States Government Procurements |
| ASTM D 664 : 2011 : REV A | Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration |
| ASTM E 1157 : 1987 : R2001 : EDT 1 | Standard Specification for Sampling and Testing of Reusable Laboratory Glassware |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.