• Shopping Cart
    There are no items in your cart

ASTM E 563 : 2022

Current

Current

The latest, up-to-date edition.

Standard Practice for Preparation and Use of an Ice-Point Bath as a Reference Temperature

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

02-08-2022

€49.35
Excluding VAT

Committee
E 20
DocumentType
Standard Practice
Pages
4
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

1.1This practice covers a method of preparing, maintaining, and using a temperature reference bath of a mixture of shaved ice and water, saturated with air at a pressure of 101 325 Pa (1 atm).

1.2An industrial practice for relating values referenced to the ice point and to the water triple point on the ITS-90 is included.

1.3Methods to promote uniformity of bath temperature by mechanical stirring or agitation are not described in detail.

1.4Methods of approximating the ice point, as by thermostatically-controlled refrigeration, are not covered by this practice.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM E 2730 : 2022 Standard Guide for Calibration and Use of Thermocouple Reference Junction Probes in Evaluation of Electronic Reference Junction Compensation Circuits
ASTM D 2162 : 2021 Standard Practice for Basic Calibration of Master Viscometers and Viscosity Oil Standards
ASTM D 445 : 2021 : EDT 1 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM E 220 : 2019 Standard Test Method for Calibration of Thermocouples By Comparison Techniques
ASTM D 70/D70M : 2021 Standard Test Method for Specific Gravity and Density of Semi-Solid Asphalt Binder (Pycnometer Method)
ASTM E 601 : 2020 Standard Guide for Measuring Electromotive Force (EMF) Stability of Base-Metal Thermoelement Materials With Time in Air
ASTM D 2532 : 2017 Standard Test Method for Viscosity and Viscosity Change After Standing at Low Temperature of Aircraft Turbine Lubricants
ASTM E 2251 : 2014 : R2021 Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
ASTM E 2877 : 2012 : R2019 Standard Guide for Digital Contact Thermometers
ASTM D 7552 : 2009 : R2014 Standard Test Method for Determining the Complex Shear Modulus (G*) Of Bituminous Mixtures Using Dynamic Shear Rheometer
ASTM D 8164 : 2021 Standard Guide for Digital Contact Thermometers for Petroleum Products, Liquid Fuels, and Lubricant Testing
ASTM D 1754/D1754M : 2020 Standard Test Method for Effects of Heat and Air on Asphaltic Materials (Thin-Film Oven Test)
ASTM D 7962 : 2021 Standard Practice for Determination of Minimum Immersion Depth and Assessment of Temperature Sensor Measurement Drift
ASTM D 7175 : 2015 Standard Test Method for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer
ASTM E 644 : 2011(R2019) Standard Test Methods for Testing Industrial Resistance Thermometers
ASTM D 3829 : 2020 : REV A Standard Test Method for Predicting the Borderline Pumping Temperature of Engine Oil
ASTM D 4693 : 2007 : R2021 Standard Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings
ASTM E 2820 : 2013 : R2019 Standard Test Method for Evaluating Thermal EMF Properties of Base-Metal Thermocouple Connectors
ASTM E 879 : 2020 Standard Specification for Thermistor Sensors for General Purpose and Laboratory Temperature Measurements
ASTM E 2846 : 2020 Standard Guide for Thermocouple Verification
ASTM E 1 : 2014 : R2020 Standard Specification for ASTM Liquid-in-Glass Thermometers
ASTM E 452 : 2002 : R2018 Standard Test Method for Calibration of Refractory Metal Thermocouples Using a Radiation Thermometer
ASTM D 6821 : 2020 : REV A Standard Test Method for Low Temperature Viscosity of Drive Line Lubricants in a Constant Shear Stress Viscometer
ASTM E 207 : 2021 Standard Test Method for Thermal EMF Test of Single Thermoelement Materials by Comparison With Reference Thermoelement of Similar EMF-Temperature Properties
ASTM D 6896 : 2020 : REV A Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature
ASTM E 2593 : 2017 Standard Guide for Accuracy Verification of Industrial Platinum Resistance Thermometers
ASTM D 61 : 2015 : R2019 Standard Test Method for Softening Point of Pitches (Cube-in-Water Method)
ASTM D 6703 : 2019 Standard Test Method for Automated Heithaus Titrimetry
ASTM D 7279 : 2020 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids by Automated Houillon Viscometer
ASTM D 4684 : 2020 : REV A Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature
ASTM D 5/D5M : 2020 Standard Test Method for Penetration of Bituminous Materials
ASTM D 2726/D2726M : 2021 Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Asphalt Mixtures
ASTM D 8278 : 2020 Standard Specification for Digital Contact Thermometers for Test Methods Measuring Flow Properties of Fuels and Lubricants

ASTM E 344 : 2020 Terminology Relating to Thermometry and Hydrometry
ASTM E 344 : 2023 Terminology Relating to Thermometry and Hydrometry

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.