ASTM E 646 : 2016 : R2024
Current
The latest, up-to-date edition.
Standard Test Method for Tensile Strain-Hardening Exponents (n -Values) of Metallic Sheet Materials
Hardcopy , PDF
English
15-11-2024
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
E 28
|
| DocumentType |
Test Method
|
| Pages |
10
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This test method covers the determination of a strain-hardening exponent by tension testing of metallic sheet materials for which plastic-flow behavior obeys the power curve given in the introduction.
Note 1:A single power curve may not be a satisfactory fit to the entire stress-strain curve between yield and necking. If such is the case, more than one value of the strain-hardening exponent may be obtained (2) by agreement using this test method.
1.2This test method is specifically for metallic sheet materials with thicknesses of at least 0.005 in. (0.13 mm) but not greater than 0.25 in. (6.4 mm). The method has successfully been and may be applied to other forms and thicknesses by agreement
1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Note 2:The value of the strain-hardening exponent, n, has no units and is independent of the units used in its determination
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 1006 : 2021 | Standard Practice for Analysis and Interpretation of Physics Dosimetry Results from Test Reactor Experiments |
| ASTM A 1079 : 2017 : R2023 | Standard Specification for Steel Sheet, Complex Phase (CP), Dual Phase (DP) and Transformation Induced Plasticity (TRIP), Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process |
| ASTM A 792/A792M : 2023 | Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process |
| ASTM A 875/A875M : 2023 | Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process |
| ASTM A 1046/A1046M : 2024 | Standard Specification for Steel Sheet, Zinc-Aluminum-Magnesium Alloy-Coated by the Hot-Dip Process |
| ASTM A 1083/A1083M : 2023 | Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, Produced by Twin-Roll Casting Process |
| ASTM A 463/A463M : 2022 | Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process |
| ASTM E 2448 : 2022 | Standard Test Method for Determining the Superplastic Properties of Metallic Sheet Materials |
| ASTM A 1008/A1008M : 2024 | Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Required Hardness, Solution Hardened, and Bake Hardenable |
| ASTM A 1088 : 2013(R2019) | Standard Specification for Steel, Sheet, Cold-Rolled, Complex Phase (CP), Dual Phase (DP) and Transformation Induced Plasticity (TRIP) |
| ASTM A 653/A653M : 2023 | Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process |
| ASTM E 2218 : 2023 | Standard Test Method for Determining Forming Limit Curves |
| ASTM E 706 : 2023 | Standard Master Matrix for Light-Water Reactor Pressure Vessel Surveillance Standards |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.