ASTM E 676 : 2002 : R2019
Current
The latest, up-to-date edition.
Standard Specification for Interchangeable Taper-Ground Joints
Hardcopy , PDF
English
01-01-2019
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 14.04, 2015 Defines designations, tolerances and dimensions for the ground surfaces of interchangeable taper-ground joints for industrial and laboratory equipment in full-length, medium-length, short-length and international-length grindings (ISO K-6 series) grindings.
| Committee |
E 41
|
| DocumentType |
Standard
|
| Pages |
4
|
| ProductNote |
Reconfirmed 2002
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This specification covers designations, dimensions, and tolerances for only the ground surfaces of interchangeable taper-ground joints for laboratory and industrial equipment in full-length, medium-length, short-length, and international-length (ISO K-6 series) grindings.
Note 1:The dimensions pertaining to full-length, medium-length, and short-length joints, other than for the tolerance on length of grind, were taken directly from the now obsolete Commercial Standard CS 21.
Note 2:Tolerances on the diameters of the international-length joints do not agree with those given in ISO Recommendation R 383. These tolerances have been established to agree with those of CS 21 in order to prevent the negative projection (large end of inner joint being smaller than large end of outer joint) permitted by ISO.
Note 3:Although glass is the most commonly used material for ground joints, other materials may be used as specified. Taper-ground joints constructed from glass should be of suitable chemical and thermal properties in accordance with Specification E438. Joints should be as free as possible of visible defects and conform to Specification E671.
1.2The following precautionary caveat pertains only to the Test Method portion, Section 4, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.3This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 1157 : 1987 : R2006 | Standard Specification for Sampling and Testing of Reusable Laboratory Glassware |
| ASTM E 1133 : 1986 : R2010 | Standard Practice for Performance Testing of Packaged Laboratory Apparatus for United States Government Procurements |
| ASTM E 1133 : 1986 : R2000 | Standard Practice for Performance Testing of Packaged Laboratory Apparatus for United States Government Procurements |
| ASTM E 438 : 1992 | SPECIFICATION FOR GLASSES IN LABORATORY APPARATUS |
| ASTM E 1157 : 1987 : R2018 : EDT 1 | Standard Specification for Sampling and Testing of Reusable Laboratory Glassware |
| ASTM E 1157 : 1987 : R1996 | Standard Specification for Sampling and Testing of Reusable Laboratory Glassware |
| ISO 383:1976 | Laboratory glassware — Interchangeable conical ground joints |
| ASTM E 1157 : 1987 : R2011 | Standard Specification for Sampling and Testing of Reusable Laboratory Glassware |
| ASTM E 920 : 1997 : R2024 | Standard Specification for Commercially Packaged Laboratory Apparatus |
| ASTM E 921 : 1997 : R2022 | Standard Specification for Export Packaged Laboratory Apparatus |
| ASTM E 1133 : 1986 : R2005 | Standard Practice for Performance Testing of Packaged Laboratory Apparatus for United States Government Procurements |
| ASTM E 438 : 1992 : R2018 | Standard Specification for Glasses in Laboratory Apparatus |
| ASTM E 1133 : 1986 : R2022 | Standard Practice for Performance Testing of Packaged Laboratory Apparatus for United States Government Procurements |
| ASTM E 1133 : 1986 : R1996 : EDT 1 | Standard Practice for Performance Testing of Packaged Laboratory Apparatus for United States Government Procurements |
| ASTM E 671 : 1998 : R2022 | Standard Specification for Maximum Permissible Thermal Residual Stress in Annealed Glass Laboratory Apparatus |
| ASTM E 438 : 1992 : R2024 | Standard Specification for Glasses in Laboratory Apparatus |
| ASTM E 921 : 1997 : R2016 | Standard Specification for Export Packaged Laboratory Apparatus |
| ASTM E 1133 : 1986 : R2016 | Standard Practice for Performance Testing of Packaged Laboratory Apparatus for United States Government Procurements |
| ASTM E 1157 : 1987 : R2001 : EDT 1 | Standard Specification for Sampling and Testing of Reusable Laboratory Glassware |
| ASTM E 671 : 1998 : R2016 | Standard Specification for Maximum Permissible Thermal Residual Stress in Annealed Glass Laboratory Apparatus |
| ASTM E 920 : 1997 : R2019 | Standard Specification for Commercially Packaged Laboratory Apparatus |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.