ASTM E 72 : 2022
Current
The latest, up-to-date edition.
Standard Test Methods of Conducting Strength Tests of Panels for Building Construction
Hardcopy , PDF
English
21-10-2022
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
E 06
|
| DocumentType |
Test Method
|
| Pages |
14
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1These test methods cover the following procedures for determining the structural properties of segments of wall, floor, and roof constructions:
| Section | |
| Test Specimens | 3 |
| Loading | 4 |
| Deformation Measurements | 5 |
| Reports | 6 |
| Precision and Accuracy | 7 |
| TESTING WALLS | |
| Significance and Use | 8 |
| Compressive Load | 9 |
| Tensile Load | 10 |
| Transverse Load—Specimen Horizontal | 11 |
| Transverse Load—Specimen Vertical | 12 |
| Concentrated Load | 13 |
| Impact Load—See Test Methods E695 and E661 | |
| Racking Load—Evaluation of Sheathing Materials | 14 |
| Racking Load—Evaluation of Sheathing Materials (Wet) | 15 |
| TESTING FLOORS | |
| Significance and Use | 16 |
| Transverse Load | 17 |
| Concentrated Load | 18 |
| Impact Load—See Test Methods E695 and E661 | |
| TESTING ROOFS | |
| Section | |
| Significance and Use | 19 |
| Transverse Load | 20 |
| Concentrated Load | 21 |
| APPENDIX | |
| Technical Interpretation | Appendix X1 |
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 2126 : 2019 | Standard Test Methods for Cyclic (Reversed) Load Test for Shear Resistance of Vertical Elements of the Lateral Force Resisting Systems for Buildings |
| ASTM C 956 : 2004 : R2019 | Standard Specification for Installation of Cast-In-Place Reinforced Gypsum Concrete |
| ASTM C 887 : 2020 | Standard Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar |
| ASTM C 90 : 2022 | Standard Specification for Loadbearing Concrete Masonry Units |
| ASTM E 2969 : 2018 | Standard Test Methods for Transverse Load Tests on Panels Used in Wall Construction |
| ASTM D 3841 : 2021 | Standard Specification for Glass-Fiber-Reinforced Polyester Plastic Panels |
| ASTM C 208 : 2022 | Standard Specification for Cellulosic Fiber Insulating Board |
| ASTM E 2570/E2570M : 2007 : R2019 | Standard Test Methods for Evaluating Water-Resistive Barrier (WRB) Coatings Used under Exterior Insulation and Finish Systems (EIFS) or EIFS with Drainage |
| ASTM C 1852 : 2020 | Standard Guide for Product Selection/Delivery Systems for Aerosol Foam Sealants and Adhesives |
| ASTM D 2394 : 2017 : R2022 | Standard Test Methods for Simulated Service Testing of Wood and Wood-Based Finish Flooring |
| ASTM E 1803 : 2014 : R2022 | Standard Test Methods for Determining Strength Capacities of Structural Insulated Panels |
| ASTM E 2322 : 2022 | Standard Test Method for Conducting Transverse and Concentrated Load Tests on Panels used in Floor and Roof Construction |
| ASTM E 695 : 2022 | Standard Test Method of Measuring Relative Resistance of Wall, Floor, and Roof Construction to Impact Loading |
| ASTM E 4 : 2021 | Standard Practices for Force Calibration and Verification of Testing Machines |
| ASTM E 661 : 2022 | Standard Test Method for Performance of Wood and Wood-Based Floor and Roof Sheathing Under Concentrated Static and Impact Loads |
| ASTM E 4 : 2024 | Standard Practices for Force Calibration and Verification of Testing Machines |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.