ASTM E 740/E740M : 2003 : R2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Fracture Testing with Surface-Crack Tension Specimens
Hardcopy , PDF
07-12-2023
English
05-10-2016
CONTAINED IN VOL. 03.01, 2016 Defines the design, preparation, and testing of surface-crack tension (SCT) specimens.
Committee |
E 08
|
DevelopmentNote |
Supersedes ASTM E 740. (02/2011)
|
DocumentType |
Standard Practice
|
Pages |
9
|
ProductNote |
Reconfirmed 2016
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This practice covers the design, preparation, and testing of surface-crack tension (SCT) specimens. It relates specifically to testing under continuously increasing force and excludes cyclic and sustained loadings. The quantity determined is the residual strength of a specimen having a semielliptical or circular-segment fatigue crack in one surface. This value depends on the crack dimensions and the specimen thickness as well as the characteristics of the material.
1.2Metallic materials that can be tested are not limited by strength, thickness, or toughness. However, tests of thick specimens of tough materials may require a tension test machine of extremely high capacity. The applicability of this practice to nonmetallic materials has not been determined.
1.3This practice is limited to specimens having a uniform rectangular cross section in the test section. The test section width and length must be large with respect to the crack length. Crack depth and length should be chosen to suit the ultimate purpose of the test.
1.4Residual strength may depend strongly upon temperature within a certain range depending upon the characteristics of the material. This practice is suitable for tests at any appropriate temperature.
1.5Residual strength is believed to be relatively insensitive to loading rate within the range normally used in conventional tension tests. When very low or very high rates of loading are expected in service, the effect of loading rate should be investigated using special procedures that are beyond the scope of this practice.
Note 1:Further information on background and need for this type of test is given in the report of ASTM Task Group E24.01.05 on Part-Through-Crack Testing (1).2
1.6The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM C 1421 : 2018 | Standard Test Methods for Determination of Fracture Toughness of Advanced Ceramics at Ambient Temperature |
ASTM E 8/E8M : 2016 : REV A : EDT 1 | Standard Test Methods for Tension Testing of Metallic Materials |
ASTM E 1823 : 2012 : REV : EDT 0 | Standard Terminology Relating to Fatigue and Fracture Testing |
ASTM E 1823 : 2007 : REV A | Standard Terminology Relating to Fatigue and Fracture Testing |
ASTM E 8/E8M : 2021 | Standard Test Methods for Tension Testing of Metallic Materials |
ASTM E 1823 : 2009 : REV A | Standard Terminology Relating to Fatigue and Fracture Testing |
ASTM E 466 : 2015 : REDLINE | Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials |
ASTM E 466 : 1996 | Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials |
ASTM E 399 : 2020 : REV A | Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness of Metallic Materials |
ASTM E 399 : 2023 | Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness of Metallic Materials |
ASTM E 1823 : 2005 : REV A : EDT 1 | Standard Terminology Relating to Fatigue and Fracture Testing |
ASTM E 1823 : 2010 : REV A | Standard Terminology Relating to Fatigue and Fracture Testing |
ASTM E 1823 : 2021 | Standard Terminology Relating to Fatigue and Fracture Testing |
ASTM E 8/E8M : 2022 | Standard Test Methods for Tension Testing of Metallic Materials |
ASTM E 1823 : 2009 : REV B | Standard Terminology Relating to Fatigue and Fracture Testing |
ASTM E 1823 : 2013-07 | TERMINOLOGY RELATING TO FATIGUE AND FRACTURE TESTING |
ASTM E 1823 : 2012 : REV D | Standard Terminology Relating to Fatigue and Fracture Testing |
ASTM E 1823 : 2012 : REV B | Standard Terminology Relating to Fatigue and Fracture Testing |
ASTM E 466 : 2021 | Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials |
ASTM E 466 : 2015 | Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials |
ASTM E 561 : 2020 | Standard Test Method for <emph type="bdit">K<inf>R</inf></emph> Curve Determination |
ASTM E 561 : 2022 | Standard Test Method for <emph type="bdit">K<inf>R</inf></emph> Curve Determination |
ASTM E 4 : 2021 | Standard Practices for Force Calibration and Verification of Testing Machines |
ASTM E 338 : 2003 | Standard Test Method of Sharp-Notch Tension Testing of High-Strength Sheet Materials (Withdrawn 2010) |
ASTM E 1823 : 1996 : R2002 | Standard Terminology Relating to Fatigue and Fracture Testing |
ASTM E 1823 : 1996 : EDT 1 | Standard Terminology Relating to Fatigue and Fracture Testing |
ASTM E 1823 : 2012 : REV A | Standard Terminology Relating to Fatigue and Fracture Testing |
ASTM E 1823 : 2007 | Standard Terminology Relating to Fatigue and Fracture Testing |
ASTM E 1823 : 2023 | Standard Terminology Relating to Fatigue and Fracture Testing |
ASTM E 561 : 2023 | Standard Test Method for <emph type="bdit">K<inf>R</inf></emph> Curve Determination |
ASTM E 399 : 2022 | Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness of Metallic Materials |
ASTM E 561 : 2021 | Standard Test Method for <emph type="bdit">K<inf>R</inf></emph> Curve Determination |
ASTM E 1823 : 2013 | Standard Terminology Relating to Fatigue and Fracture Testing |
ASTM E 1823 : 2012 : REV C | Standard Terminology Relating to Fatigue and Fracture Testing |
ASTM E 1823 : 2020 : REV B | Standard Terminology Relating to Fatigue and Fracture Testing |
ASTM E 8/E8M : 2016-09 | TEST METHODS FOR TENSION TESTING OF METALLIC MATERIALS |
ASTM E 1823 : 2005 : REV A | Standard Terminology Relating to Fatigue and Fracture Testing |
ASTM E 1823 : 2011 | Standard Terminology Relating to Fatigue and Fracture Testing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.