ASTM E 88 : 2011 : R2017
Current
The latest, up-to-date edition.
Standard Practice for Sampling Nonferrous Metals and Alloys in Cast Form for Determination of Chemical Composition
Hardcopy , PDF
English
01-09-2017
CONTAINED IN VOL. 03.05, 2017 Defines the sampling, for the determination of chemical composition of nonferrous metals and alloys, excluding aluminum, in cast form for remelting or mechanical working.
Committee |
E 01
|
DocumentType |
Standard Practice
|
Pages |
2
|
ProductNote |
Reconfirmed 2017
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
1.1This practice covers the sampling, for the determination of chemical composition (Note 1) of nonferrous metals and alloys, excluding aluminum, in cast form for remelting or mechanical working.
1.1.1Refer to Practice E255 for copper and copper alloys.
Note 1:The selection of correct portions of material and the preparation of a representative sample from such portions are necessary prerequisites to every analysis, the analysis being of no value unless the sample actually represents the average composition of the material from which it was selected.
1.2When agreed upon between the purchaser and the manufacturer, the heat sample and analysis may be accepted as representative of the composition of the metal. In such cases, each lot must be properly identified with the heats from which it was made.
1.3This practice is intended to cover the general principles of sampling applicable to nonferrous metals in cast form and is not intended to supersede or replace existing specification requirements for sampling of a particular material.
1.4The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM E 255 : 2023 | Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition |
ASTM E 135 : 2023 | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
ASTM E 135 : 2024 | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
ASTM E 135 : 2021 : REV A | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
ASTM E 255 : 1991 : R1997 | Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition |
ASTM E 135 : 2003 : REV B | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
ASTM E 135 : 2023 : REV A | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
ASTM E 135 : 2002 : REV A | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
ASTM E 135 : 2022 : REV B | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
ASTM E 135 : 2022 : REV A | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
ASTM E 135 : 2021 | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
ASTM E 135 : 2003 | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
ASTM E 135 : 2003 : REV C | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
ASTM E 135 : 2022 | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
ASTM E 135 : 2020 : REV B | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
ASTM E 255 : 2007 : R2014 | Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition (Withdrawn 2023) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.