ASTM E 930 : 1999
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Estimating the Largest Grain Observed in a Metallographic Section (ALA Grain Size)
Hardcopy , PDF
11-11-2014
English
10-04-1999
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 03.01, 2015 Specifies simple manual procedures for measuring the size of the largest grain cross-section observed on a metallographically prepared plane section.
| Committee |
E 04
|
| DocumentType |
Test Method
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1 These test methods describe simple manual procedures for estimating the size of the largest grain observed on a metallographically prepared plane section.
1.2 These test methods shall only be valid for microstructures containing outlier course grains, where their population is too sparse for grain size determination by Test Methods E112.
1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| BS ISO 13383-1 : 2012 | FINE CERAMICS (ADVANCED CERAMICS, ADVANCED TECHNICAL CERAMICS) - MICROSTRUCTURAL CHARACTERIZATION - PART 1: DETERMINATION OF GRAIN SIZE AND SIZE DISTRIBUTION |
| ISO 13067:2011 | Microbeam analysis Electron backscatter diffraction Measurement of average grain size |
| ASTM E 1181 : 2002 : R2015 | Standard Test Methods for Characterizing Duplex Grain Sizes |
| ASTM F 799 : 2011 : REDLINE | SPECIFICATION FOR COBALT-28CHROMIUM-6MOLYBDENUM ALLOY FORGINGS FOR SURGICAL IMPLANTS (UNS R31537, R31538, R31539) |
| BS EN ISO 13383-1:2016 | Fine ceramics (advanced ceramics, advanced technical ceramics). Microstructural characterization Determination of grain size and size distribution |
| ASTM E 1181 : 2002 : R2008 : EDT 1 | Standard Test Methods for Characterizing Duplex Grain Sizes |
| SAE AS7101C | National Aerospace and Defense Contractors Accreditation Program (NADCAP) General Requirements for Materials Test Laboratory Accreditation Program |
| I.S. EN ISO 13383-1:2016 | FINE CERAMICS (ADVANCED CERAMICS, ADVANCED TECHNICAL CERAMICS) - MICROSTRUCTURAL CHARACTERIZATION - PART 1: DETERMINATION OF GRAIN SIZE AND SIZE DISTRIBUTION (ISO 13383-1:2012) |
| ASTM E 1181 : 2002 : R2008 | Standard Test Methods for Characterizing Duplex Grain Sizes |
| ASTM E 1181 : 2002 | Standard Test Methods for Characterizing Duplex Grain Sizes |
| BS ISO 13067:2011 | Microbeam analysis. Electron backscatter diffraction. Measurement of average grain size |
| SAE AS7471H | Bolts and Screws, Nickel Alloy, UNS N07001 Tensile Strength 165 ksi, Corrosion and Heat Resistant Procurement Specification |
| ASTM E 1382 : 1997 | Standard Test Methods for Determining Average Grain Size Using Semiautomatic and Automatic Image Analysis |
| 11/30212232 DC : DRAFT AUG 2011 | BS ISO 13383-1 - FINE CERAMICS (ADVANCED CERAMICS, ADVANCED TECHNICAL CERAMICS) - MICROSTRUCTURAL CHARACTERIZATION - PART 1: DETERMINATION OF GRAIN SIZE AND SIZE DISTRIBUTION |
| ASTM E 1382 : 1997 : R2010 | Standard Test Methods for Determining Average Grain Size Using Semiautomatic and Automatic Image Analysis |
| ISO 13383-1:2012 | Fine ceramics (advanced ceramics, advanced technical ceramics) — Microstructural characterization — Part 1: Determination of grain size and size distribution |
| EN ISO 13383-1:2016 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Microstructural characterization - Part 1: Determination of grain size and size distribution (ISO 13383-1:2012) |
| DIN ISO 13067:2015-12 | Microbeam analysis - Electron backscatter diffraction - Measurement of average grain size (ISO 13067:2011) |
| ASTM E 1382 : 1997 : R2004 | Standard Test Methods for Determining Average Grain Size Using Semiautomatic and Automatic Image Analysis |
| SAE AMS5884D | Iron-Nickel Alloy, Bars, Forgings, and Rings 42Fe - 37.5Ni - 14Co - 4.8Cb(Nb) - 1.6Ti Solution Heat Treated, Precipitation Hardenable Multiple Melted, High Temperature, Low Expansion |
| ASTM E 1382 : 1997 : R2015 | Standard Test Methods for Determining Average Grain Size Using Semiautomatic and Automatic Image Analysis |
| ASTM E 7 : 2017 : REDLINE | Standard Terminology Relating to Metallography |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.