ASTM F 1316 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Measuring the Transmissivity of Transparent Parts
Hardcopy , PDF
13-06-2023
English
25-06-2018
1.1 This test method describes an apparatus and procedure that is suitable for measuring the transmissivity of large, thick, or curved transparent parts including parts already installed. This test method is limited to transparencies that are relatively neutral with respect to wavelength (not highly colored).1.2 Since the transmissivity (transmission coefficient) is a ratio of two luminance values, it has no units. The units of luminance recorded in the intermediate steps of this test method are not critical; any recognized units of luminance (for example, foot-lamberts or candelas per square metre) are acceptable for use, as long as use is consistent.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Committee |
F 07
|
DocumentType |
Test Method
|
Pages |
5
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method describes an apparatus and procedure that is suitable for measuring the transmissivity of large, thick, or curved transparent parts including parts already installed. This test method is limited to transparencies that are relatively neutral with respect to wavelength (not highly colored).
1.2Since the transmissivity (transmission coefficient) is a ratio of two luminance values, it has no units. The units of luminance recorded in the intermediate steps of this test method are not critical; any recognized units of luminance (for example, foot-lamberts or candelas per square metre) are acceptable for use, as long as use is consistent.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM F 942 : 2018 | Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures |
ASTM F 1863 : 2016 | Standard Test Method for Measuring the Night Vision Goggle-Weighted Transmissivity of Transparent Parts |
ASTM F 790 : 2023 | Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures |
ASTM F 1863 : 2016 : R2021 | Standard Test Method for Measuring the Night Vision Goggle-Weighted Transmissivity of Transparent Parts |
ASTM F 790 : 2018 | Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures |
ASTM D 1003 : 2007 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
ASTM D 1003 : 2013 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
ASTM D 1003 : 2007 : EDT 1 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
ASTM D 1003 : 2011 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
ASTM D 1003 : 2021 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
ASTM D 1003 : 2000 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
ASTM D 1003 : 2011 : EDT 1 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
ASTM D 1003 : 1992 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.