ASTM F 1394 : 1992 : R2020
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
Standard Test Method for Determination of Particle Contribution from Gas Distribution System Valves (Withdrawn 2023)
Hardcopy , PDF
07-05-2020
English
07-05-2020
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
F 01
|
| DocumentType |
Test Method
|
| Pages |
27
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Withdrawn
|
| Supersedes |
1.1This test method covers gas distribution system components intended for installation into a high-purity gas distribution system.
1.1.1This test method describes a procedure designed to draw statistically significant comparisons of particulate generation performance of valves tested under aggressive conditions.
1.1.2This test method is not intended as a methodology for monitoring on-going particle performance once a particular valve has been tested.
1.2This test method utilizes a condensation nucleus counter (CNC) applied to in-line gas valves typically used in semiconductor applications. It applies to automatic and manual valves of various types (such as diaphragms or bellows), 6.3 through 12.7-mm (1/4through 1/2-in.) size. For applications of this test method to larger valves, see the table in the appendix.
1.2.1Valves larger than 12.7 mm (1/2in.) can be tested by this methodology. The test stand must be sized accordingly. Components larger than 12.7 mm (1/2in.) should be tested while maintaining a Reynolds number of 20 000 to 21 000. This is the Reynolds number for 12.7-mm (1/2-in.) components tested at a velocity of 30.5 m/s (100 ft/s).
1.3Limitations:
1.3.1This test method is applicable to total particle count greater than the minimum detection limit (MDL) of the condensation nucleus particle counter and does not consider classifying data into various size ranges.
1.3.1.1It is questionable whether significant data can be generated from nondynamic components (such as fittings and short lengths of tubing) to compare, with statistical significance, to the data generated from the spool piece. For this reason, this test method cannot reliably support comparisons between these types of components.
1.3.1.2If detection or classification of particles, or both, in the size range of laser particle counter (LPC) technology is of interest, an LPC can be utilized for testing components. Flow rates, test times, sampling apparatus, and data analysis outlined in this test method do not apply for use with an LPC. Because of these variations, data from CNCs are not comparable to data from LPCs.
1.3.2This test method specifies flow and mechanical stress conditions in excess of those considered typical. These conditions should not exceed those recommended by the manufacturer. Actual performance under normal operating conditions may vary.
1.3.3The test method is limited to nitrogen or clean dry air. Performance with other gases may vary.
1.3.4This test method is intended for use by operators who understand the use of the apparatus at a level equivalent to six months of experience.
1.3.5The appropriate particle counter manufacturer's operating and maintenance manuals should be consulted when using this test method.
1.4The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 6, Hazards.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.