• There are no items in your cart

ASTM F 1430/F1430M : 2018 : REDLINE

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Test Method for Acoustic Emission Testing of Insulated and Non-Insulated Aerial Personnel Devices with Supplemental Load Handling Attachments

Available format(s)

PDF

Superseded date

02-09-2020

Language(s)

English

Published date

01-03-2018

€74.48
Excluding VAT

CONTAINED IN VOL. 10.03, 2018 Defines a procedure for acoustic emission (AE) testing of aerial personnel devices (APDs) with supplemental load handling attachments.

Committee
F 18
DevelopmentNote
Supersedes ASTM F 1430. (05/2010)
DocumentType
Redline
Pages
14
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

1.1This test method describes a procedure for acoustic emission (AE) testing of aerial personnel devices (APDs) with supplemental load handling attachments.

1.1.1Equipment Covered—This test method covers the following types of vehicle-mounted aerial personnel devices with supplemental load handling attachments:

1.1.1.1Extensible-boom APDs,

1.1.1.2Articulating-boom APDs, and

1.1.1.3Any combination of 1.1.1.1 and 1.1.1.2.

1.1.2Equipment Not Covered—This test method does not cover any of the following equipment:

1.1.2.1Aerial personnel devices without supplemental load handling attachments,

1.1.2.2Digger-derricks with platform,

1.1.2.3Cranes with platform, and

1.1.2.4Aerial devices with load-lifting capabilities located anywhere other than adjacent to the platform.

Note 1:This test method is not intended to be a stand-alone NDT method for the verification of the structural integrity of an aerial device. Other NDT methods should be used to supplement the results.

1.2The AE test method is used to detect and area-locate emission sources. Verification of emission sources may require the use of other nondestructive test (NDT) methods, such as radiography, ultrasonics, magnetic particle, liquid penetrant, and visual inspection. (Warning—This test method requires that external loads be applied to the superstructure of the vehicle under test. During the test, caution must be taken to safeguard personnel and equipment against unexpected failure or instability of the vehicle or components.)

1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASNT SNT TC 1A : 2016 TOPICAL OUTLINES FOR QUALIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL
ASTM F 914 : 2003 Standard Test Method for Acoustic Emission for Insulated and Non-Insulated Aerial Personnel Devices Without Supplemental Load Handling Attachments
ASTM E 114 : 2015 : REDLINE Standard Practice for Ultrasonic Pulse-Echo Straight-Beam Contact Testing
ASTM E 750 : 2015 : REDLINE Standard Practice for Characterizing Acoustic Emission Instrumentation
ASTM E 1417/E1417M : 2016 : REDLINE Standard Practice for Liquid Penetrant Testing
ASTM E 650 : 1997 Standard Guide for Mounting Piezoelectric Acoustic Emission Sensors
ASTM E 976 : 2015 : REDLINE Standard Guide for Determining the Reproducibility of Acoustic Emission Sensor Response

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.