ASTM F 1506 : 2019 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Performance Specification for Flame Resistant and Electric Arc Rated Protective Clothing Worn by Workers Exposed to Flames and Electric Arcs
Hardcopy , PDF
29-06-2020
English
01-12-2019
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
F 18
|
| DocumentType |
Standard
|
| Pages |
9
|
| ProductNote |
THIS STANDARD ALSO REFERES TO : Method 61,Method 132,Method 135,Method 158,29 CFR 1910.138
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This performance specification identifies minimum performance requirements to determine the (a) arc rating of fabrics, (b) flame resistance of fabrics and subassemblies, (c) mechanical durability of the fabrics and subassemblies, (d) the minimum garment construction and performance requirements, and (e) the garment labeling requirements for the completed protective clothing worn by workers exposed to flames and electric arcs.
1.1.1The minimum requirements for garment labeling are intended to provide end users with adequate information to select garments with the appropriate arc rating.
1.1.2End users are required to perform an assessment to determine the level of hazard and the required arc rating of the protective clothing for their individual hazards.
1.1.2.1The end user risk assessments are outside the scope of this standard.
1.2This performance specification does not address coated or laminated protective clothing commonly used for rainwear applications in an arc hazard environment. Performance requirements related to this category of protective clothing are detailed in Specification F1891.
1.3This performance specification does not address hand protection. Performance and test requirements related to hand protection are detailed in OSHA 1910.138, Specification D120, and Test Method F2675/F2675M.
1.4The care and maintenance requirements for laundering electric arc flash protective clothing are outside the scope of this standard. Refer to Guides F1449 or F2757 related to industrial or home laundering.
1.5This standard should be used to evaluate and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions. It should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions.
1.5.1The results of this evaluation may be used as elements of a fire-risk assessment that takes into account all of the factors that are pertinent to an assessment of the fire hazard of a particular end use.
1.6The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.7The following precautionary caveat pertains only to the test methods portion, Section 7, of this performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 2178 : 2017 : REV B | Standard Test Method for Determining the Arc Rating and Standard Specification for Eye or Face Protective Products |
| ASTM E 1549/E1549M : 2013 : R2016 | Standard Specification for ESD Controlled Garments Required in Cleanrooms and Controlled Environments for Spacecraft for Non-Hazardous and Hazardous Operations |
| ASTM F 1958/F1958M : 2012 | Standard Test Method for Determining the Ignitability of Non-flame-Resistant Materials for Clothing by Electric Arc Exposure Method Using Mannequins (Withdrawn 2021) |
| ASTM F 2302 : 2019 | Standard Performance Specification for Labeling Protective Clothing Which Provides Resistance to Incidental Exposures to Heat or Open Flame |
| ASTM F 2621/F2621M : 2019 | Standard Practice for Determining Response Characteristics and Design Integrity of Arc Rated Finished Products and Evaluating other Products in an Electric Arc Exposure |
| ASTM F 2757 : 2009 : R2016 | Standard Guide for Home Laundering Care and Maintenance of Flame, Thermal and Arc Resistant Clothing |
| ASTM F 1449 : 2020 | Standard Guide for Industrial Laundering Care and Maintenance of Flame Resistant or Arc Rated Clothing |
| ASTM F 1449 : 2008 : R2015 | Standard Guide for Industrial Laundering of Flame, Thermal, and Arc Resistant Clothing |
| ASTM D 5034 : 2009 : R2017 | Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.