![header thumbnail](/images/publishers\astm_cover.gif)
ASTM F 1545 : 2015 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges
Hardcopy , PDF
11-11-2021
English
02-06-2015
Committee |
F 17
|
DocumentType |
Standard
|
Pages |
9
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers factory-made plastic-lined ferrous metal pipe, fittings, and flanges intended primarily for conveying corrosive fluids. Requirements for materials, workmanship, dimensions, design, fabrication, working pressure and temperatures, test methods, qualification requirements, and markings are included.
1.1.1This specification does not define the suitability of different liner materials to various chemical and operating environments. Refer to the manufacturer's chemical resistance data for suitability recommendations.
1.1.2This specification does not include products coated with plastics.
1.2This specification covers plastic-lined pipe, flanges, and fittings as listed in Table 1. Pressure limitations shall be in accordance with ASME B16 Standards, except reduced pressure limitations may be established by the manufacturer, considering both pressure and temperature limitations of the ferrous metal housing and the sealing ability of the liner.
Note 1:In this specification, propylene plastics cover those materials defined as both polypropylene plastics and propylene plastics in Terminology F412. Both materials are identified as “PP” on the product. Note that this is at variance with Terminology D1600, where “PP” is the abbreviation for polypropylene.
1.3The plastic-lined flanged pipe and fitting assemblies are limited to temperatures shown in Table 2. End users should consult with manufacturers as to the likely result of using a particular lined piping component at temperatures below the rated minimum.
Note 2:The temperature limitations are based on noncorrosive test conditions. Use in specific aggressive environments may alter temperature limitations. In such instances, specific temperature limits shall be established by mutual agreement between the purchaser and the manufacturer.
1.4The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM F 412 : 2020 : REV A | Standard Terminology Relating to Plastic Piping Systems |
ASTM F 412 : 2019 | Standard Terminology Relating to Plastic Piping Systems |
ASTM A 135/A135M : 2021 | Standard Specification for Electric-Resistance-Welded Steel Pipe |
ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 4101 : 2001 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 4101 : 2001 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 4101 : 2006 : REV B | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 4101 : 2005 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM A 234/A234M : 2010 | Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service |
ASTM A 53/A53M : 2020 | Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless |
ASTM D 5575 : 2007 | Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers |
ASTM D 3222 : 2018 : REV A | Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials |
ASTM A 312/A312M : 2021 | Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes |
ASTM D 4101 : 2000 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 5575 : 1999 | Standard Specification for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers |
ASTM A 48/A48M : 2003 : R2021 | Standard Specification for Gray Iron Castings |
ASTM A 182/A182M : 2021 | Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service |
ASTM D 4101 : 2008 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 3159 : 1998 | Standard Specification for Modified ETFE-Fluoropolymer Molding and Extrusion Materials |
ASTM D 1457 : 1983 | Standard Specification for PTFE Molding and Molding and Extrusion Materials |
ASTM F 714 : 2013 : R2019 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter |
ASTM D 4101 : 2006 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 4101 : 2004 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 2116 : 2002 | Standard Specification for FEP-Fluorocarbon Molding and Extrusion Materials |
ASTM D 4894 : 1998 : REV A | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
ASTM D 2116 : 2016 | Standard Specification for FEP Resin Molding and Extrusion Materials |
ASTM A 182/A182M : 2011 | Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service |
ASTM A 216/A216M : 2021 | Standard Specification for Steel Castings, Carbon, Suitable for Fusion Welding, for High-Temperature Service |
ASTM D 3222 : 1999 | Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials |
ASTM D 4101 : 2014 : EDT 2 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 3222 : 2018 | Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials |
ASTM D 4101 : 2010 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 4101 : 2011 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 4101 : 2005 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 3159 : 2006 | Standard Specification for Modified ETFE-Fluoropolymer Molding and Extrusion Materials |
ASTM D 3350 : 2000 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
ASTM D 4894 : 2007 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
ASTM D 3307 : 2016 | Standard Specification for Perfluoroalkoxy (PFA) Resin Molding and Extrusion Materials |
ASTM D 4101 : 2007 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM A 312/A312M : 2019 | Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes |
ASTM D 3307 : 2000 | Standard Specification for Perfluoroalkoxy (PFA)-Fluorocarbon Resin Molding and Extrusion Materials |
ASTM D 3307 : 2021 | Standard Specification for Perfluoroalkoxy (PFA) Resin Molding and Extrusion Materials |
ASTM D 4101 : 2002 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM F 714 : 2021 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter |
ASTM D 3350 : 2008 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
ASTM D 4101 : 2003 : REV B | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 3350 : 2021 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
ASTM D 3350 : 2002 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
ASTM D 4101 : 2002 : REV B | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 1505 : 2003 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 3350 : 2014 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
ASTM D 4101 : 2009 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 2116 : 2007 : R2012 | Standard Specification for FEP-Fluorocarbon Molding and Extrusion Materials |
ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 4895 : 1998 | Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion |
ASTM D 4101 : 2006 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM F 714 : 2021 : REV A | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter |
ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 3307 : 2004 | Standard Specification for Perfluoroalkoxy (PFA)-Fluorocarbon Resin Molding and Extrusion Materials |
ASTM D 3350 : 2004 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
ASTM A 182/A182M : 2020 | Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service |
ASTM A 105/A105M : 1998 | Standard Specification for Carbon Steel Forgings for Piping Applications |
ASTM D 3350 : 2002 : REV A | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
ASTM D 3222 : 2020 | Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials |
ASTM A 216/A216M : 2018 | Standard Specification for Steel Castings, Carbon, Suitable for Fusion Welding, for High-Temperature Service |
ASTM D 3222 : 2021 | Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials |
ASTM D 3350 : 2012 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
ASTM D 4101 : 2004 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 3350 : 2001 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
ASTM D 4101 : 1982 : R1988 : EDT 1 | Standard Specification for Propylene Plastic Injection and Extrusion Materials |
ASTM D 3307 : 2010 | Standard Specification for Perfluoroalkoxy (PFA)-Fluorocarbon Resin Molding and Extrusion Materials |
ASTM D 4101 : 2017 | Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials |
ASTM A 105/A105M : 2021 | Standard Specification for Carbon Steel Forgings for Piping Applications |
ASTM D 3350 : 2012 : EDT 1 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
ASTM A 135/A135M : 2020 | Standard Specification for Electric-Resistance-Welded Steel Pipe |
ASTM D 3222 : 2005 | Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials |
ASTM D 3159 : 2004 | Standard Specification for Modified ETFE-Fluoropolymer Molding and Extrusion Materials |
ASTM D 4894 : 2004 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
ASTM D 4101 : 2014 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 3159 : 2010 | Standard Specification for Modified ETFE-Fluoropolymer Molding and Extrusion Materials |
ASTM D 4895 : 2018 | Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion |
ASTM D 5575 : 2018 | Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers |
ASTM D 1505 : 1968 : R1979 | Standard Test Method for Density Of Plastics By The Density-Gradient Technique |
ASTM D 1457 : 1992 | Specification for Polytetrafluorethylene (PTFE) Molding and Extrusion Materials (Withdrawn 1996) |
ASTM A 234/A234M : 2001 : REV A | Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service |
ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
ASTM D 3307 : 2001 | Standard Specification for Perfluoroalkoxy (PFA)-Fluorocarbon Resin Molding and Extrusion Materials |
ASTM D 4101 : 2010 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 3350 : 2010 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
ASTM D 3307 : 2006 | Standard Specification for Perfluoroalkoxy (PFA)-Fluorocarbon Resin Molding and Extrusion Materials |
ASTM D 3222 : 2005 : R2015 | Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials |
ASTM D 3159 : 2015 | Standard Specification for Modified ETFE Fluoropolymer Molding and Extrusion Materials |
ASTM D 3222 : 2005 : R2010 | Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials |
ASTM D 4895 : 2004 | Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion |
ASTM D 4101 : 2003 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 4894 : 2015 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
ASTM D 1505 : 2010 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
ASTM D 3350 : 2006 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
ASTM D 1505 : 2018 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
ASTM D 4101 : 2003 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM A 182/A182M : 2001 : REV A | Standard Specification for Forged or Rolled Alloy-Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service |
ASTM D 4894 : 2019 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
ASTM A 48/A48M : 2003 : R2016 | Standard Specification for Gray Iron Castings |
ASTM D 3350 : 2010 : REV A | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
ASTM D 1505 : 1998 : EDT 1 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
ASTM D 4894 : 2007 : R2012 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
ASTM D 2116 : 1997 | Standard Specification for FEP-Fluorocarbon Molding and Extrusion Materials |
ASTM D 4895 : 2016 | Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion |
ASTM D 4101 : 2002 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 4895 : 2010 | Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion |
ASTM D 5575 : 2007 : R2013 | Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers |
ASTM D 2116 : 2016 : R2021 | Standard Specification for FEP Resin Molding and Extrusion Materials |
ASTM D 4101 : 2017 : EDT 1 | Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 2116 : 2007 | Standard Specification for FEP-Fluorocarbon Molding and Extrusion Materials |
ASTM D 4101 : 2014 : EDT 1 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 3307 : 2008 | Standard Specification for Perfluoroalkoxy (PFA)-Fluorocarbon Resin Molding and Extrusion Materials |
ASTM A 53/A53M : 2018 | Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless |
ASTM D 3350 : 2005 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
ASTM D 4895 : 2015 | Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion |
ASTM D 3159 : 2020 | Standard Specification for Modified ETFE Fluoropolymer Molding and Extrusion Materials |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.