Skip to content
Please enter a keyword to search

  • ASTM F 1588 : 1996 : R2015

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Standard Test Method for Constant Tensile Load Joint Test (CTLJT)

    Available format(s):  Hardcopy, PDF

    Superseded date:  12-11-2019

    Language(s):  English

    Published date:  01-08-2015

    Publisher:  American Society for Testing and Materials

    Add To Cart

    Abstract - (Show below) - (Hide below)

    CONTAINED IN VOL. 08.04, 2017 Specifies to demonstrate that a joint in a plastic piping system is resistant to the effects of long-term creep.

    Scope - (Show below) - (Hide below)

    1.1The constant tensile load joint test (CTLJT) is designed to demonstrate that a joint in a plastic piping system is resistant to the effects of long-term creep.

    1.1.1The joint is subjected to an internal pressure at least equal to its operating pressure and a sustained axial tensile load for a specified time period, usually 1000 h. The joint shall not leak, nor may the pipe completely pull out for the test duration. The total axial stress is set by the referencing document.

    1.1.2Some typical conditions for testing of joints on polyethylene pipe are described in Appendix X1.

    1.2This test is usually performed at 73°F (22.8°C).

    1.3The CTLJT was developed to demonstrate the long-term resistance to pullout of mechanical joints on polyethylene gas pipe. The CTLJT has also been successfully applied to the evaluation of other components of plastic piping systems. These applications are discussed in Appendix X1.

    1.4The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    General Product Information - (Show below) - (Hide below)

    Committee F 17
    Document Type Test Method
    Product Note Reconfirmed 2015
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM F 2145 : 2013 : R2018 Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing
    ASTM F 1924 : 2019 Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing
    ASTM F 1924 : 2012 Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing
    ASTM F 1973 : 2013 : R2018 Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems
    ASTM F 1948 : 2015 Standard Specification for Metallic Mechanical Fittings for Use on Outside Diameter Controlled Thermoplastic Gas Distribution Pipe and Tubing

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM D 1600 : 1999 Standard Terminology for Abbreviated Terms Relating to Plastics
    ASTM D 2513 : 2006 Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2122 : 1998 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
    ASTM D 2513 : 2016 Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2003 : REV A Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2012 : REV A Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2008 : REV A Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2011 : REV B Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2006 : REV A Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2009 Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2004 Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 1987 Standard Specification for Thermoplastic Gas Pressure Piping Systems
    ASTM D 2513 : 2011 : REV C Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
    ASME B31.8 : 2016 Gas Transmission and Distribution Piping Systems
    ASTM D 2513 : 2016 : REV A Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2013 Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 1999 Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2009 : REV A Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 1600 : 2007 Standard Terminology for Abbreviated Terms Relating to Plastics
    ASTM D 2513 : 2003 : REV B Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 1600 : 2013 Standard Terminology for Abbreviated Terms Relating to Plastics
    ASTM D 2513 : 2001 : REV A Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2001 Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 1600 : 2014 Standard Terminology for Abbreviated Terms Relating to Plastics
    CFR 49(PTS186-199) : 0 TRANSPORTATION
    ASTM D 2513 : 2001 : REV A : EDT 1 Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 1600 : 2008 Standard Terminology for Abbreviated Terms Relating to Plastics
    ASTM D 2513 : 2011 : EDT 1 Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2014 : EDT 1 Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2014 Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2000 Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2007 : REV A Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2019 Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2011 Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2122 : 1998 : EDT 1 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
    ASTM D 2513 : 2008 : REV B Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2017-01 SPECIFICATION FOR POLYETHYLENE (PE) GAS PRESSURE PIPE, TUBING, AND FITTINGS
    ASTM D 2513 : 2003 Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2006 : REV B Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 1600 : 2018 Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
    ASTM D 2122 : 2016 : REDLINE Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
    ASTM D 2513 : 2007 : REV B : EDT 1 Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2008 Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2018 : REV A Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2122 : 1998 : R2004 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
    ASTM D 2122 : 2016 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
    ASTM D 2513 : 2007 Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2007 : REV B Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2012 : REV A : EDT 1 Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2122 : 1998 : R2010 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
    ASTM D 2513 : 2018 Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2011 : REV A Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2513 : 2012 Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics
    ASTM D 2513 : 2004 : REV A Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 2122 : 2015 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
    ASTM D 2513 : 2005 Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective