ASTM F 1667 : 2020
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
Hardcopy , PDF
01-07-2021
English
12-02-2021
Committee |
F 16
|
DocumentType |
Standard
|
Pages |
47
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1.
Note 1:Fastener ductility information is presented in Table 2 and dimensional information in Tables 3–65.
1.2Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine.
1.3The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.4Fasteners in this specification are sold in bulk (loose) form and are collated for loading into the magazine of an application tool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond, paper tape, plastic strip, plastic carrier, wire, etc.) and relative orientation of collated fasteners are not within the scope of this standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 228/D228M : 2019 : REV A | Standard Test Methods for Sampling, Testing, and Analysis of Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing and Waterproofing |
ASTM C 1861 : 2020 | Standard Specification for Lathing and Furring Accessories, and Fasteners, for Interior and Exterior Portland Cement-Based Plaster |
ASTM B 900 : 2016 | Standard Practice for Packaging of Copper and Copper Alloy Mill Products for U.S. Government Agencies |
ASTM D 7672 : 2019 | Standard Specification for Evaluating Structural Capacities of Rim Board Products and Assemblies |
ASTM E 2266 : 2011 : R2019 | Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion |
ASTM D 6251/D6251M : 2019 | Standard Specification for Wood-Cleated Panelboard Shipping Boxes |
ASTM D 3462/D3462M : 2019 | Standard Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules |
ASTM B 660 : 2015 | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
ASTM D 6880/D6880M : 2019 | Standard Specification for Wood Boxes |
ASTM D 7349/D7349M : 2015(R2019) | Standard Test Method for Determining the Capability of Roofing and Waterproofing Materials to Seal Around Fasteners |
ASTM D 6254/D6254M : 2020 | Standard Specification for Wirebound Pallet-Type Wood Boxes |
ASTM D 7470 : 2008 : R2015 | Standard Practice for Evaluating Elevated Temperature Performance of End-Jointed Lumber Studs |
ASTM D 8257/D8257M : 2020 | Standard Specification for Mechanically Attached Polymeric Roof Underlayment Used in Steep Slope Roofing |
ASTM D 6573/D6573M : 2013 : R2020 | Standard Specification for General Purpose Wirebound Shipping Boxes |
ASTM D 7478/D7478M : 2011 : R2017 | Standard Specification for Heavy Duty Sheathed Wood Crates |
ASTM A 641/A641M : 2019 | Standard Specification for Zinc–Coated (Galvanized) Carbon Steel Wire |
ASTM D 6039/D6039M : 2018 | Standard Specification for Open and Covered Wood Crates |
ASTM D 1185 : 1998 : REV A : R2017 | Standard Test Methods for Pallets and Related Structures Employed in Materials Handling and Shipping |
ASTM F 1575 : 2017 | Standard Test Method for Determining Bending Yield Moment of Nails |
ASTM D 1761 : 2020 | Standard Test Methods for Mechanical Fasteners in Wood and Wood-Based Materials |
ASTM F 547 : 2017 | Standard Terminology of Nails for Use with Wood and Wood-Base Materials |
ASTM D 7374 : 2008 : R2015 | Standard Practice for Evaluating Elevated Temperature Performance of Adhesives Used in End-Jointed Lumber |
ASTM D 6255/D6255M : 2018 | Standard Specification for Steel or Aluminum Slotted Angle Crates |
ASTM D 7989 : 2020 | Standard Practice for Demonstrating Equivalent In-Plane Lateral Seismic Performance to Wood-Frame Shear Walls Sheathed with Wood Structural Panels |
ASTM D 6256/D6256M : 2016 | Standard Specification for Wood-Cleated Shipping Boxes with Skidded, Load-Bearing Bases |
ASTM F 3359 : 2019 | Standard Test Method for Determining Bending Yield Moment of Staples |
ASTM F 537 : 2001 : R2019 | Standard Specification for Design, Fabrication, and Installation of Fences Constructed of Wood and Related Materials |
ASTM D 228/D228M : 2021 | Standard Test Methods for Sampling, Testing, and Analysis of Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing and Waterproofing |
ASTM A 641/A641M : 2019 | Standard Specification for Zinc–Coated (Galvanized) Carbon Steel Wire |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.