ASTM F 1671/F1671M : 2022
Current
The latest, up-to-date edition.
Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Blood-Borne Pathogens Using Phi-X174 Bacteriophage Penetration as a Test System
Hardcopy , PDF
English
13-01-2022
Committee |
F 23
|
DocumentType |
Test Method
|
Pages |
11
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This test method is used to measure the resistance of materials used in protective clothing to penetration by blood-borne pathogens using a surrogate microbe under conditions of continuous liquid contact. Protective clothing material pass/fail determinations are based on the detection of viral penetration.
1.1.1This test method is not always effective in testing protective clothing materials having thick, inner liners which readily absorb the liquid assay fluid.
1.2This test method does not apply to all forms or conditions of blood-borne pathogen exposure. Users of the test method should review modes for worker/clothing exposure and assess the appropriateness of this test method for their specific applications.
1.3This test method has been specifically defined for modeling the viral penetration of Hepatitis (B and C) and Human Immunodeficiency Viruses transmitted in blood and other potentially infectious body fluids. Inferences for protection from other pathogens must be assessed on a case-by-case basis.
1.4This test method addresses only the performance of materials or certain material constructions (for example, seams) used in protective clothing and determined to be viral resistant. This test method does not address the design, overall construction and components, or interfaces of garments or other factors which may affect the overall protection offered by the protective clothing.
1.5The values stated in SI units or in other units shall be regarded separately as standard. The values stated in each system must be used independently of the other, without combining values in any way.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM F 1862/F1862M : 2017 | Standard Test Method for Resistance of Medical Face Masks to Penetration by Synthetic Blood (Horizontal Projection of Fixed Volume at a Known Velocity) |
ASTM F 1819 : 2019 | Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Synthetic Blood Using a Mechanical Pressure Technique |
ASTM F 3352 : 2019 | Standard Specification for Isolation Gowns Intended for Use in Healthcare Facilities |
ASTM F 903 : 2024 | Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Liquids |
ASTM F 903 : 2018 | Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Liquids |
ASTM F 1670/F1670M : 2017 : REV A | Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Synthetic Blood |
ASTM D 1331 : 2020 | Standard Test Methods for Surface and Interfacial Tension of Solutions of Paints, Solvents, Solutions of Surface-Active Agents, and Related Materials |
ASTM D 3862 : 2013 : R2019 | Standard Test Method for Retention Characteristics of 0.2-µm Membrane Filters Used in Routine Filtration Procedures for the Evaluation of Microbiological Water Quality |
ASTM F 1670/F1670M : 2024 | Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Synthetic Blood |
ASTM F 1670/F1670M : 2024 : REV A | Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Synthetic Blood |
ASTM D 1331 : 2020 : R2024 | Standard Test Methods for Surface and Interfacial Tension of Solutions of Paints, Solvents, Solutions of Surface-Active Agents, and Related Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.