ASTM F 2019 : 2011 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic (GRP) Cured-in-Place Thermosetting Resin Pipe (CIPP)
16-05-2020
English
01-09-2011
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 08.04, 2018 Defines the procedures for the reconstruction of pipelines and conduits (4 to 60 in. (100 to 1500 mm) diameter) by the pulled-in place installation of a resinimpregnated, flexible fabric tube into an existing conduit followed by inflation with compressed air.
| Committee |
F 17
|
| DocumentType |
Redline
|
| Pages |
10
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1 This practice covers the procedures for the reconstruction of pipelines and conduits (4 to 60 in. (100 to 1500 mm) diameter) by the pulled-in place installation of a resin-impregnated, flexible fabric tube into an existing conduit followed by inflation with compressed air (see Fig. 1). The resin/fabric tube can be cured by either the flow through the fabric tube of mixed air and steam or hot water or by use of ultraviolet light. When cured, the finished cured-in-place pipe will be continuous and tight fitting. This reconstruction process can be used in a variety of gravity flow applications such as sanitary sewers, storm sewers, process piping, electrical conduits, ventilation systems, and pressure applications.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
FIG. 1 Cured-In-Place Pipe Installation Method (Air/Steam)
| ASTM D 5813 : 2004 : R2008 | Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems |
| ASTM F 3240 : 2017 | Standard Practice for Installation of Seamless Molded Hydrophilic Gaskets (SMHG) for Long-Term Watertightness of Cured-in-Place Rehabilitation of Main and Lateral Pipelines |
| ASTM D 5813 : 2004 | Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems |
| ASTM D 5813 : 2004 : R2012 | Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems |
| ASTM D 3859 : 2015 : REDLINE | Standard Test Methods for Selenium in Water |
| ASTM D 543 : 2014 : REDLINE | Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents |
| ASTM D 578 : 2005 | Standard Specification for Glass Fiber Strands |
| ASTM F 1216 : 2016 : REDLINE | Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube |
| ASTM D 790 : 2017 : REDLINE | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
| ASTM D 3039/D3039M : 2017 : REDLINE | Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials |
| AWWA M28 : 2014 | REHABILITATION OF WATER MAINS |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.