ASTM F 22 : 2013 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Hydrophobic Surface Films by the Water-Break Test
05-01-2022
English
25-11-2013
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 15.03, 2015 Defines the detection of the presence of hydrophobic (nonwetting) films on surfaces and the presence of hydrophobic organic materials in processing environments.
| Committee |
E 21
|
| DocumentType |
Redline
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This test method covers the detection of the presence of hydrophobic (nonwetting) films on surfaces and the presence of hydrophobic organic materials in processing environments. When properly conducted, the test will enable detection of molecular layers of hydrophobic organic contaminants. On very rough or porous surfaces, the sensitivity of the test may be significantly decreased.
1.2The values stated in SI units are to be regarded as the standard. The inch-pound values given in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 5620 : 1994 : R1999 | Standard Test Method for Evaluating Thin Film Fluid Lubricants in a Drain and Dry Mode Using a Pin and Vee Block Test Machine |
| MIL-PRF-32405 Base Document:2013 | CLEANER, HAND WIPE, FOR AVIATION AND MISSILE SYSTEMS, METALLIC SUBSTRATES, LOW OR EXEMPT VOC |
| ASTM A 380 : 2006 | Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems |
| DWA-M 143-20:2018 | TEST METHOD FOR DROP IMPACT RESISTANCE OF BLOW-MOLDED THERMOPLASTIC CONTAINERS |
| ASTM D 2625 : 1994 : R2003 | Standard Test Method for Endurance (Wear) Life and Load-Carrying Capacity of Solid Film Lubricants (Falex Pin and Vee Method) |
| SAE AS5272E | Lubricant, Solid Film, Heat Cured, Corrosion Inhibiting, Procurement Specification |
| ASTM D 2510 : 1994 : R2012 | Standard Test Method for Adhesion of Solid Film Lubricants |
| SSPC-GUIDE 22 : 2016 | USE AND RETENTION OF PRE-CONSTRUCTION PRIMERS ON STEEL IN SHIPBUILDING |
| IPC HDBK 830 : A | GUIDELINES FOR DESIGN, SELECTION AND APPLICATION OF CONFORMAL COATINGS |
| P-W-2891 Revision A:2002 | WIPE SOLVENTS, EXEMPT AND NON-EXEMPT |
| MIL L 46147 : B | LUBRICANT, SOLID FILM, AIR CURED (CORROSION INHIBITING) |
| MIL-DTL-14538 Revision D:1999 | CHROMIUM PLATING, BLACK (ELECTRODEPOSITED) |
| ASTM D 2625 : 1994 : R2010 | Standard Test Method for Endurance (Wear) Life and Load-Carrying Capacity of Solid Film Lubricants (Falex Pin and Vee Method) |
| ASTM D 2510 : 1994 : R1998 | Standard Test Method for Adhesion of Solid Film Lubricants |
| SAE AS6450B | Lubricant Application, Solid Film, Heat Cured, Potable Water, Hydraulic, and Other Fluid Systems |
| ASTM F 2661 : 2007 | Standard Test Method for Determining the Tribological Behavior and the Relative Lifetime of a Fluid Lubricant using the Spiral Orbit Tribometer |
| ASTM D 2625 : 1994 : R1998 | Standard Test Method for Endurance (Wear) Life and Load-Carrying Capacity of Solid Film Lubricants (Falex Pin and Vee Method) |
| MIL-PRF-46010 Revision H:2013 | LUBRICANT, SOLID FILM, HEAT CURED, CORROSION INHIBITING NATO CODE S-1738 |
| ASTM D 2510 : 1994 : R2017 | Standard Test Method for Adhesion of Solid Film Lubricants |
| MIL L 0046010 : D | LUBRICANT, SOLID FILM, HEAT CURED, CORROSION INHIBITING |
| MIL-PRF-46147 Revision D:2008 | LUBRICANT, SOLID FILM, AIR CURED, CORROSION INHIBITING |
| ASTM D 2625 : 1994 : R2015 | Standard Test Method for Endurance (Wear) Life and Load-Carrying Capacity of Solid Film Lubricants (Falex Pin and Vee Method) |
| ASTM D 5620 : 1994 : R2004 | Standard Test Method for Evaluating Thin Film Fluid Lubricants in a Drain and Dry Mode Using a Pin and Vee Block Test Machine (Withdrawn 2010) |
| SAE AS5528C | Lubricant Application, Solid Film, Heat Cured, Corrosion Inhibiting |
| SAE AS7489 | Standard Requirements for Aerospace Organic Coatings Applicator Certification |
| NASA MSFC PROC 547 : 2014 | POLYURETHANE COATING, APPLICATION OF |
| NASA PRC 8001 : 2013 | PROCESS SPECIFICATION FOR DRY-FILM LUBRICANT APPLICATION |
| MIL L 46010 : D | LUBRICANT, SOLID FILM, HEAT CURED, CORROSION INHIBITING |
| ASTM F 2664 : 2011 : REDLINE | Standard Guide for Assessing the Attachment of Cells to Biomaterial Surfaces by Physical Methods |
| ASTM D 2510 : 1994 : R2006 | Standard Test Method for Adhesion of Solid Film Lubricants |
| ASTM A 380/A380M : 2017 | Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems |
| ASTM F 2661 : 2007 : R2015 | Standard Test Method for Determining the Tribological Behavior and the Relative Lifetime of a Fluid Lubricant using the Spiral Orbit Tribometer |
| ASTM F 21 : 2014 : REDLINE | Standard Test Method for Hydrophobic Surface Films by the Atomizer Test |
| ASTM D 7490 : 2013 : REDLINE | Standard Test Method for Measurement of the Surface Tension of Solid Coatings, Substrates and Pigments using Contact Angle Measurements |
| ASTM F 21 : 2014 : REDLINE | Standard Test Method for Hydrophobic Surface Films by the Atomizer Test |
| ASTM D 5946 : 2017 : REDLINE | Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.