ASTM F 22 : 2021
Current
The latest, up-to-date edition.
Standard Test Method for Hydrophobic Surface Films by the Water-Break Test
Hardcopy , PDF
English
10-12-2021
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
E 21
|
| DocumentType |
Test Method
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This test method covers the detection of the presence of hydrophobic (nonwetting) films on surfaces and the presence of hydrophobic organic materials in processing environments. When properly conducted, the test will enable detection of molecular layers of hydrophobic organic contaminants. On very rough or porous surfaces, the sensitivity of the test may be significantly decreased.
1.2Units—The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 2625 : 2020 | Standard Test Method for Endurance (Wear) Life and Load-Carrying Capacity of Solid Film Lubricants (Falex Pin and Vee Method) |
| ASTM F 2661 : 2007 : R2015 | Standard Test Method for Determining the Tribological Behavior and the Relative Lifetime of a Fluid Lubricant using the Spiral Orbit Tribometer |
| ASTM F 21 : 2020 | Standard Test Method for Hydrophobic Surface Films by the Atomizer Test |
| ASTM F 2664 : 2019 : EDT 1 | Standard Guide for Assessing the Attachment of Cells to Biomaterial Surfaces by Physical Methods |
| ASTM D 2510 : 1994 : R2017 | Standard Test Method for Adhesion of Solid Film Lubricants |
| ASTM A 380/A380M : 2017 | Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems |
| ASTM D 7490 : 2013 : R2022 | Standard Test Method for Measurement of the Surface Tension of Solid Coatings, Substrates and Pigments using Contact Angle Measurements |
| ASTM D 2578 : 2017 | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films |
| ASTM C 813 : 2020 : R2024 | Standard Test Method for Hydrophobic Contamination on Glass by Contact Angle Measurement |
| ASTM D 7334 : 2008 : R2022 | Standard Practice for Surface Wettability of Coatings, Substrates and Pigments by Advancing Contact Angle Measurement |
| ASTM D 7490 : 2013 | Standard Test Method for Measurement of the Surface Tension of Solid Coatings, Substrates and Pigments using Contact Angle Measurements |
| ASTM D 7334 : 2008 : R2013 | Standard Practice for Surface Wettability of Coatings, Substrates and Pigments by Advancing Contact Angle Measurement |
| ASTM C 813 : 2020 | Standard Test Method for Hydrophobic Contamination on Glass by Contact Angle Measurement |
| ASTM D 2578 : 2023 | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.