ASTM F 2257 : 2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Wrought Seamless or Welded and Drawn 18 Chromium-14Nickel-2.5Molybdenum Stainless Steel Small Diameter Tubing for Surgical Implants (UNS S31673)
Hardcopy , PDF
14-10-2022
English
11-02-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
F 04
|
| DocumentType |
Standard
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers the requirements for wrought 18chromium-14nickel-2.5molybdenum stainless steel tubing used for the manufacture of surgical implants. Material shall conform to the applicable requirements of Specification F138 (for seamless) or Specification F139 (for welded and drawn). This specification addresses those product variables that differentiate small-diameter medical grade tubing from the bar, wire, sheet, and strip product forms covered in these specifications.
1.2This specification applies to cold finished straight length tubing with 3 mm [0.125 in.] and smaller nominal outside diameter (OD) and 0.5 mm [0.020 in.] and thinner nominal wall thickness.
1.3The specifications in 2.1 are referred to as the ASTM material standard(s) in this specification.
1.4The values stated in either inch-pound or SI units are to be regarded separately as standard. Inch-pound units are shown in parentheses. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
| ASTM F 2181 : 2014 | Standard Specification for Wrought Seamless Stainless Steel Tubing for Surgical Implants |
| ASTM E 8/E8M : 2016 : REV A : EDT 1 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM E 29 : 2013 : R2019 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM E 8/E8M : 2021 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM F 2181 : 2008 | Standard Specification for Wrought Seamless Stainless Steel Tubing for Surgical Implants |
| ASTM F 2181 : 2020 | Standard Specification for Wrought Seamless Stainless Steel Tubing for Surgical Implants |
| ASTM F 2181 : 2009 | Standard Specification for Wrought Seamless Stainless Steel Tubing for Surgical Implants |
| ASTM A 632 : 1998 | Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing (Small-Diameter) for General Service |
| ASTM F 2181 : 2002 : REV A | Standard Specification for Wrought Seamless Stainless Steel Tubing for Surgical Implants |
| ASTM E 8/E8M : 2022 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM F 2181 : 2014 | Standard Specification for Wrought Seamless Stainless Steel Tubing for Surgical Implants |
| ASTM F 2181 : 2002 | Standard Specification for Wrought Seamless Stainless Steel Tubing for Surgical Implants |
| ASTM E 112 : 2013 : R2021 | Standard Test Methods for Determining Average Grain Size |
| ASTM E 112 : 2013 | Standard Test Methods for Determining Average Grain Size |
| ASTM E 29 : 2022 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.