ASTM F 2376 : 2023
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Classification, Design, Manufacture, Construction, and Operation of Water Slide Systems
Hardcopy , PDF
20-06-2024
English
01-06-2023
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
F 24
|
| DocumentType |
Standard Practice
|
| Pages |
13
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice applies to the classification, design, manufacture, construction, auditing, major modification, and operation of water slide systems. Water slide systems shall be defined as rides intended for use by riders in bathing attire where the action of the ride involves possible and purposeful immersion of the rider's body either in whole or in part in water, and uses circulating water to mobilize or lubricate the rider’s transportation along a purpose built path. This includes slides used with or without vehicles as defined below. The terms water slides, waterslides, and slides shall be considered equivalent when used in this practice.
1.1.1Owner/operator requirements of this standard are required of all water slide systems regardless of date of construction.
1.1.2The design, manufacture and construction of an existing water slide or portions of a water slide system unaffected by a major modification shall meet the standard requirements in existence at the time of the construction.
1.2For the purposes of this practice, a water slide system includes:
1.2.1The flume,
1.2.2The water-circulation system,
1.2.3The starting platform with associated means of access and egress,
1.2.4The structural supports,
1.2.5Vehicles or other aquatic accessories that are part of the water slide as defined by the manufacturer, and
1.2.6Means of slide termination.
1.3This practice shall not apply to:
1.3.1Any water slides installed in private residences,
1.3.2Water flume amusement rides where contact with water is merely incidental (for example, log flume rides, shoot-the-chutes),
1.3.3Amusement rides and devices whose design criteria are specifically addressed in another ASTM standard,
1.3.4Lazy river type attractions operating at constant elevation, constructed in the ground,
1.3.5Inflatable water slides (constant air supply) that are mounted on land (refer to Practice F2374-22 for the requirements of these types of water slides),
1.3.6Inflatable water slides (captured air) that are floating on a body of water (refer to EN/ISO 25649-2017, parts 1 through 7), and
1.3.7Water slides less than 6 ft tall. (Refer to Practice F2461-20a for the requirements of slides less than 6 ft tall.)
1.4Pre-existing designs manufactured after the effective date of publication of this practice if the design is service proven or previously compliant, as defined in Terminology F747-22, and the manufacturer provides:
1.4.1A historical summary of the water slide, or major modification as defined in Terminology F747-22, and
1.4.2A statement that the design is service proven or previously compliant. Water slides and major modifications to water slides may qualify as previously compliant for five years following the date of publication of this practice. Thereafter, water slides and major modifications to water slides must qualify as service proven or meet the requirements of this practice.
1.4.3Service proven or previously compliant designs shall comply with Section 4.
1.5The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
Note 1:The conversion factor from inch-pound to metric units is 1 in. = 25.4 mm, and 1 lb = 4.4482 N.
1.6This practice includes an Appendix, which provides additional information to enhance the user's understanding of and application of the criteria presented in this practice, for example, rationale, background, drawings, interpretation, or commentary. The information in the Appendix shall not be considered a mandatory part of this practice.
1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 3133 : 2021 | Standard Practice for Classification, Design, Manufacture, Construction, Maintenance, and Operation of Stationary Wave Systems |
| ASTM F 747 : 2023 | Standard Terminology Relating to Amusement Rides and Devices |
| ASTM F 2783 : 2020 | Standard Practice for Design, Manufacture, Operation, Maintenance, and Inspection of Amusement Rides and Devices, in Canada |
| ASTM F 3158 : 2022 | Standard Practice for Patron Transportation Conveyors Used with a Water Related Amusement Ride or Device |
| ASTM F 3493 : 2023 | Standard Practice for Measuring Dynamic Characteristics of Water Slide Systems Using Instrumented Humans |
| ASTM F 2461 : 2023 | Standard Practice for Manufacture, Construction, Operation, and Maintenance of Aquatic Play Equipment |
| ASTM F 3559 : 2023 | Standard Guide for ASTM F24 Standards Governing Lifecycle Management of Amusement Rides and Devices |
| ASTM F 747 : 2024 | Standard Terminology Relating to Amusement Rides and Devices |
| ASTM F 2291 : 2024 | Standard Practice for Design of Amusement Rides and Devices |
| ASTM F 2291 : 2023 : REV B | Standard Practice for Design of Amusement Rides and Devices |
| ASTM F 770 : 2024 | Standard Practice for Ownership, Operation, Maintenance, and Inspection of Amusement Rides and Devices |
| ASTM F 2974 : 2022 | Standard Practice for Auditing Amusement Rides and Devices |
| ASTM F 747 : 2024 | Standard Terminology Relating to Amusement Rides and Devices |
| ASTM F 2291 : 2023 : REV A | Standard Practice for Design of Amusement Rides and Devices |
| ASTM F 1193 : 2023 | Standard Practice for Quality, Manufacture, and Construction of Amusement Rides and Devices |
| ASTM F 1193 : 2024 | Standard Practice for Quality, Manufacture, and Construction of Amusement Rides and Devices |
| ASTM F 770 : 2023 | Standard Practice for Ownership, Operation, Maintenance, and Inspection of Amusement Rides and Devices |
| ASTM F 2974 : 2024 | Standard Practice for Auditing Amusement Rides and Devices |
| ASTM F 2974 : 2024 : REV A | Standard Practice for Auditing Amusement Rides and Devices |
| ASTM F 2291 : 2023 | Standard Practice for Design of Amusement Rides and Devices |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.