ASTM F 2777 : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Evaluating Knee Bearing (Tibial Insert) Endurance and Deformation Under High Flexion
Hardcopy , PDF
16-10-2023
English
24-08-2016
Committee |
F 04
|
DocumentType |
Test Method
|
Pages |
8
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This standard specifies a test method for determining the endurance properties and deformation, under specified laboratory conditions, of ultra high molecular weight polyethylene (UHMWPE) tibial bearing components used in bicompartmental or tricompartmental knee prosthesis designs.
1.2This test method is intended to simulate near posterior edge loading similar to the type of loading that would occur during high flexion motions such as squatting or kneeling.
1.3Although the methodology described attempts to identify physiological orientations and loading conditions, the interpretation of results is limited to an in vitro comparison between knee prosthesis designs and their ability to resist deformation and fracture under stated test conditions.
1.4This test method applies to bearing components manufactured from UHMWPE.
1.5This test method could be adapted to address unicompartmental total knee replacement (TKR) systems, provided that the designs of the unicompartmental systems have sufficient constraint to allow use of this test method. This test method does not include instructions for testing two unicompartmental knees as a bicompartmental system.
1.6The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM F 2083 : 2012 | Standard Specification for Knee Replacement Prosthesis |
ASTM F 2083 : 2006 : REV A | Standard Specification for Total Knee Prosthesis |
ASTM F 1223 : 2004 : REV A | Standard Test Method for Determination of Total Knee Replacement Constraint |
ASTM F 1223 : 2004 | Standard Test Method for Determination of Total Knee Replacement Constraint |
ASTM F 2083 : 2007 | Standard Specification for Total Knee Prosthesis |
ASTM F 2083 : 2006 | Standard Specification for Total Knee Prosthesis |
ASTM F 2083 : 2004 | Standard Specification for Total Knee Prosthesis |
ASTM F 2003 : 2002 : R2022 | Standard Practice for Accelerated Aging of Ultra-High Molecular Weight Polyethylene After Gamma Irradiation in Air |
ASTM F 2003 : 2002 | Standard Practice for Accelerated Aging of Ultra-High Molecular Weight Polyethylene after Gamma Irradiation in Air |
ASTM F 2083 : 2012 | Standard Specification for Knee Replacement Prosthesis |
ASTM F 1223 : 2008 : R2012 | Standard Test Method for Determination of Total Knee Replacement Constraint |
ASTM F 2003 : 2002 : R2015 | Standard Practice for Accelerated Aging of Ultra-High Molecular Weight Polyethylene after Gamma Irradiation in Air |
ASTM F 2083 : 2001 : REV A | Standard Specification for Total Knee Prosthesis |
ASTM F 2003 : 2002 : R2008 | Standard Practice for Accelerated Aging of Ultra-High Molecular Weight Polyethylene after Gamma Irradiation in Air |
ASTM F 1223 : 2014 | Standard Test Method for Determination of Total Knee Replacement Constraint |
ASTM F 1223 : 2003 | Standard Test Method for Determination of Total Knee Replacement Constraint |
ASTM F 2083 : 2011 | Standard Specification for Total Knee Prosthesis |
ASTM F 2083 : 2010 | Standard Specification for Total Knee Prosthesis |
ASTM F 1223 : 2005 | Standard Test Method for Determination of Total Knee Replacement Constraint |
ASTM F 2083 : 2006 : REV B | Standard Specification for Total Knee Prosthesis |
ASTM F 2083 : 2008 : EDT 1 | Standard Specification for Total Knee Prosthesis |
ASTM F 2083 : 2003 | Standard Specification for Total Knee Prosthesis |
ASTM F 2083 : 2001 | Standard Specification for Total Knee Prosthesis |
ASTM F 1223 : 1996 | Standard Test Method for Determination of Total Knee Replacement Constraint |
ASTM F 1223 : 2001 | Standard Test Method for Determination of Total Knee Replacement Constraint |
ASTM F 2083 : 2021 | Standard Specification for Knee Replacement Prosthesis (Withdrawn 2023) |
ASTM F 2003 : 2000 | Standard Guide for Accelerated Aging of Ultra-High Molecular Weight Polyethylene |
ASTM F 1223 : 2008 | Standard Test Method for Determination of Total Knee Replacement Constraint |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.