ASTM F 2779 : 2010 : R2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Commercial Radial Truck-Bus Tires to Establish Equivalent Test Severity Between a 1.707-m (67.23-in.) Diameter Roadwheel and a Flat Surface
Hardcopy , PDF
28-11-2024
English
01-10-2016
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 09.02, 2016 Specifies the procedure to identify equivalent test severity conditions between a 1.707-m diameter laboratory roadwheel surface and a flat or highway surface for commercial radial truck-bus tires.
| Committee |
F 09
|
| DocumentType |
Standard Practice
|
| Pages |
8
|
| ProductNote |
Reconfirmed 2016
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice describes the procedure to identify equivalent test severity conditions between a 1.707-m diameter laboratory roadwheel surface and a flat or highway surface for commercial radial truck-bus tires.
1.1.1Tire operational severity, as defined as the running or operational temperature for certain specified internal tire locations, is not the same for these two test conditions. It is typically higher for the laboratory roadwheel at equal load, speed and inflation pressure conditions due to the curvature effect.
1.1.2The practice applies to specific operating conditions of load range F through L for such commercial radial truck-bus tires.
1.1.3The specific operating conditions under which the procedures of the practice are valid and useful are completely outlined in Section 6 (Limitations) of this standard.
1.1.4It is important to note that this standard is composed of two distinct formats:
1.1.4.1The usual text format as published in this volume of the Book of Standards (Vol 09.02).
1.1.4.2A special interactive electronic format that uses a special software tool, designated as prediction profilers or profilers. This special profiler may be used to determine laboratory test conditions that provide equivalent tire internal temperatures for the tread centerline, belt edge, or ply ending region for the two operational conditions, that is, the curved laboratory roadwheel and flat highway test surfaces.
1.2The prediction profilers are based on empirically developed linear regression models obtained from the analysis of a large database that was obtained from a comprehensive experimental test program for roadwheel and flat surface testing of typical commercial truck and bus tires. See Section 7 and References (1, 2)2,3 for more details.
1.2.1For users viewing the standard on CD-ROM or PDF, with an active and working internet connection, the profilers can be accessed on the ASTM website by clicking on the links in 7.5 and 7.6.
1.2.2For users viewing the standard in a printed format, the profilers can be accessed by entering the links to the ASTM website in 7.5 and 7.6 into their internet browsers.
1.3For this standard, SI units shall be used, except where indicated.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM F 2869 : 2010 : R2016 | Standard Practice for Radial Light Truck Tires to Establish Equivalent Test Severity Between a 1.707-m (67.23-in.) Diameter Rotating Roadwheel and a Flat Surface |
| ASTM F 538 : 2013 : REDLINE | Standard Terminology Relating to the Characteristics and Performance of Tires |
| ASTM F 538 : 2024 | Standard Terminology Relating to Characteristics and Performance of Tires |
| IEEE/ASTM SI_10-2010 | American National Standard for Metric Practice |
| ASTM F 538 : 2013 | Standard Terminology Relating to the Characteristics and Performance of Tires |
| SAE J1269_200609 | Rolling Resistance Measurement Procedure for Passenger Car, Light Truck, and Highway Truck and Bus Tires |
| CFR 29(PT1910.1000 TO END) : 0 | LABOR - OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR |
| ASTM F 538 : 2022 | Standard Terminology Relating to Characteristics and Performance of Tires |
| ASTM F 538 : 2021 | Standard Terminology Relating to Characteristics and Performance of Tires |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.