ASTM F 2785 : 2018 : REV A
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings
Available format(s)
Hardcopy , PDF
Superseded date
21-12-2020
Superseded by
Language(s)
English
Published date
13-11-2018
Important note : Users cannot be edited or removed once added to your Multi user PDF.This specification covers requirements and test methods for the characterization of polyamide 12 pipe, tubing, and fittings for use in fuel gas mains and services for direct burial and reliner applications.
| Committee |
F 17
|
| DocumentType |
Standard
|
| Pages |
14
|
| ProductNote |
THIS STANDARD ALSO REFERS TO ANSI B16.40, ANSI B31.8, Fed. Std. No. 123, OPS Part 192 Title 49, 49 CFR Part 192.283,
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers requirements and test methods for the characterization of polyamide 12 pipe, tubing, and fittings for use in fuel gas mains and services for direct burial and reliner applications. The pipe and fittings covered by this specification are intended for use in the distribution of natural gas.
1.1.1Pipe and fittings covered by this specification shall not be joined using taper pipe threads. Joining methods qualified in accordance with the requirements of Title 49 CFR Part 192.283 are acceptable. Generic fusion guidelines are given in Appendix X1. Design considerations are discussed in Appendix X2. In-plant quality control programs are specified in Annex A1.
1.2The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1:Pipe and fittings utilizing heat fusion joining techniques produced from compounds meeting the requirements of Group 3, Class 2, and Grade 3 (PA323 or PA11) are intended for use with pipe manufactured from compounds meeting the requirements of Group 3, class 2 and Grade 3. Pipe and fittings utilizing heat fusion joining techniques produced from compounds meeting the requirements of Group 4, Class 2 and Grade 3 (PA 423 or PA12) are intended for use with pipe manufactured from compounds meeting the requirements of Group 4, Class 2 and Grade 3. As per the recommendations of the respective resin manufacturers, no cross fusion between PA 323 (PA11) and PA 423 (PA12) compounds is permitted.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Standards | Relationship |
| ISO 179:1993 | Equivalent |
| ASTM F 1733 : 2013 | Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing |
| ASTM F 1948 : 2015 | Standard Specification for Metallic Mechanical Fittings for Use on Outside Diameter Controlled Thermoplastic Gas Distribution Pipe and Tubing |
| ASTM F 3124 : 2015 : EDT 1 | Standard Practice for Data Recording the Procedure used to Produce Heat Butt Fusion Joints in Plastic Piping Systems or Fittings |
| ASTM F 2145 : 2013 : R2018 | Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing |
| ASTM F 1973 : 2013 : R2018 | Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems |
| ASTM D 2837 : 2013 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM F 1473 : 2001 : EDT 1 | Standard Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins |
| ASTM D 6779 : 2002 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 2774 : 2004 | Standard Practice for Underground Installation of Thermoplastic Pressure Piping |
| ASTM D 6779 : 2005 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM F 2897 : 2011 | Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances) |
| ASTM D 6779 : 2020 | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 6779 : 2007 : REV A | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 2290 : 2016 | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe |
| ASTM D 1598 : 2002 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 2122 : 1998 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2290 : 2019 : REV A | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe |
| ASTM D 1598 : 2015 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 1598 : 2015 : REV A | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM F 1733 : 1996 : R2002 | Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing |
| ASTM D 2837 : 2001 : REV A | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM D 6779 : 2003 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM F 2897 : 2014 | Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances) |
| ASTM F 2138 : 2001 : EDT 1 | Standard Specification for Excess Flow Valves for Natural Gas Service |
| ASTM F 1473 : 2018 | Standard Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins |
| ASTM F 1025 : 1994 : R2006 | Standard Guide for Selection and Use of Full-Encirclement-Type Band Clamps for Reinforcement or Repair of Punctures or Holes in Polyethylene Gas Pressure Pipe |
| ASTM F 1473 : 2013 | Standard Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins |
| ASTM D 6779 : 2011 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 2774 : 2001 | Standard Practice for Underground Installation of Thermoplastic Pressure Piping |
| ASTM F 2897 : 2011 : REV A : EDT 1 | Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances) |
| ASTM F 2145 : 2013 : R2018 | Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing |
| ASTM D 6779 : 2008 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 2837 : 2002 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM D 2837 : 2001 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM D 2837 : 2004 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM F 2138 : 2001 | Standard Specification for Excess Flow Valves for Natural Gas Service |
| ASTM D 6779 : 2004 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 2774 : 1994 | Standard Practice for Underground Installation of Thermoplastic Pressure Piping |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM F 1473 : 2011 | Standard Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins |
| ASTM F 2767 : 2018 | Standard Specification for Electrofusion Type Polyamide-12 Fittings for Outside Diameter Controlled Polyamide-12 Pipe and Tubing for Gas Distribution |
| ASTM F 1733 : 1996 : EDT 1 | Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 6779 : 2012 | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
| ASTM F 2138 : 2012 : R2017 | Standard Specification for Excess Flow Valves for Natural Gas Service |
| ASTM D 2290 : 2004 | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method |
| ASTM F 2145 : 2001 : R2007 | Standard Specification for Polyamide 11 (PA 11) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 Pipe and Tubing |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2837 : 2008 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM D 6779 : 2006 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 2837 : 1998 : REV A | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM F 2138 : 2012 | Standard Specification for Excess Flow Valves for Natural Gas Service |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM F 2145 : 2001 | Standard Specification for Polyamide 11 (PA 11) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 Pipe and Tubing |
| ASTM F 2145 : 2009 | Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing |
| ASTM F 1025 : 1994 : R2000 | Standard Guide for Selection and Use of Full-Encirclement-Type Band Clamps for Reinforcement or Repair of Punctures or Holes in Polyethylene Gas Pressure Pipe |
| ASTM D 1598 : 1997 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 2774 : 2008 | Standard Practice for Underground Installation of Thermoplastic Pressure Piping |
| ASTM D 2837 : 2001 : REV A : EDT 1 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM D 2837 : 2011 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM D 1599 : 2014 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1599 : 2014 : EDT 1 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM F 2897 : 2015 : REV A | Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances) |
| ASTM F 1973 : 2012 | Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems |
| ASTM D 1898 : 1968 : R1989 | Standard Practice for Sampling of Plastics (Withdrawn 1998) |
| ASTM D 2122 : 1998 : EDT 1 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM F 1973 : 2008 | Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems |
| ASTM D 1599 : 2018 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM F 1973 : 2005 | Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) Fuel Gas Distribution Systems |
| ASTM D 1599 : 1999 : R2011 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 2290 : 2000 | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method |
| ASTM F 1973 : 2002 | Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) Fuel Gas Distribution Systems |
| ASTM D 1599 : 1999 : EDT 1 | Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM F 1733 : 2007 | Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing |
| ASTM F 1025 : 1994 : R2011 | Standard Guide for Selection and Use of Full-Encirclement-Type Band Clamps for Reinforcement or Repair of Punctures or Holes in Polyethylene Gas Pressure Pipe |
| ASTM D 6779 : 2004 : REV A | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM F 1973 : 2013 | Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 6779 : 2012 : REV A | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
| ASTM F 1973 : 2013 : EDT 1 | Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems |
| ASTM F 1973 : 2013 : R2018 | Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems |
| ASTM F 2897 : 2015 | Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances) |
| ASTM F 1733 : 1996 | Standard Specification for Butt heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing |
| ASTM D 1598 : 2002 : R2008 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 6779 : 2002 : REV A | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM F 2145 : 2013 | Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing |
| ASTM F 2767 : 2012 | Standard Specification for Electrofusion Type Polyamide-12 Fittings for Outside Diameter Controlled Polyamide-12 Pipe and Tubing for Gas Distribution |
| ASTM D 2290 : 2000 : EDT 1 | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method |
| ASTM D 2122 : 1998 : R2004 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM F 2767 : 2009 | Standard Specification for Electrofusion Type Polyamide-12 Fittings for Outside Diameter Controlled Polyamide-12 Pipe and Tubing for Gas Distribution |
| ASTM D 2122 : 2016 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM F 2138 : 2009 | Standard Specification for Excess Flow Valves for Natural Gas Service |
| ASTM D 2774 : 2012 | Standard Practice for Underground Installation of Thermoplastic Pressure Piping |
| ASTM D 2290 : 2019 | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe |
| ASTM F 1473 : 2007 | Standard Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins |
| ASTM F 1973 : 1999 : EDT 2 | Standard Specification for Factory Assebled Anodeless Risers and Transition Fittings in Polyethylene (PE) Fuel Gas Distribution Systems |
| ASTM F 1733 : 2013 | Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing |
| ASTM F 1473 : 2016 | Standard Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins |
| ASTM D 1599 : 1999 : R2005 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1598 : 2002 : R2009 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 2290 : 2012 | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe |
| ASTM F 1973 : 1999 : EDT 1 | Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) Fuel Gas Distribution Systems |
| ASTM D 6779 : 2016 | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 6779 : 2007 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM F 1973 : 1999 | Standard Specification for Factory Assebled Anodeless Risers and Transition Fittings in Polyethylene (PE) Fuel Gas Distribution Systems |
| ASTM F 2897 : 2011 : REV A | Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances) |
| ASTM D 6779 : 2010 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 2774 : 2004 : EDT 1 | Standard Practice for Underground Installation of Thermoplastic Pressure Piping |
| ASTM D 2122 : 1998 : R2010 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2290 : 2008 | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method |
| ASTM D 1599 : 1999 | Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM F 1025 : 2019 | Standard Guide for Selection and Use of Full-Encirclement-Type Band Clamps for Reinforcement or Repair of Punctures or Holes in Polyethylene Gas Pressure Pipe |
| ASTM D 2122 : 2015 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM F 1473 : 1997 : EDT 1 | Standard Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins |
| ASTM D 6779 : 2017 | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 6779 : 2008 : REV A | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 6779 : 2006 : EDT 1 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 2837 : 2013 : EDT 1 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM D 2837 : 2004 : EDT 1 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.