ASTM F 288 : 1996 : R2019
Current
The latest, up-to-date edition.
Standard Specification for Tungsten Wire for Electron Devices and Lamps
Hardcopy , PDF
English
06-02-2024
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
B 10
|
| DocumentType |
Standard
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This specification covers three types of drawn wire suitable for fabrication into parts for electron tubes, lamps, and other devices; and one type of rod for metal-to-glass sealing (grid wire is excepted):
1.1.1Type 1A—Commercially pure nonsag wire (Note 2 and Note 3).
1.1.2Type 1B—Commercially pure rod suitable for metal-to-glass sealing.
1.1.3Type 2A—Thoriated filament wire containing 1 % thoria.
1.1.4Type 2B—Thoriated filament wire containing 2 % thoria.
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3Types 1A and 1B are designated as UNS R07005. Type 2A is designated as UNS R07911. Type 2B is designated as UNS R07912.
1.4The following precautionary caveat pertains only to the Chemical Analysis, Section 12 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1:A dimensional measurement method for testing nonsag tungsten wire above 0.030 in. (0.76 mm) in diameter is provided in Test Method F269.
Note 2:Acceptance of nonsag wire characteristics for particular applications of size shall be by agreement between producer and consumer based on either a flashed microstructure as shown by photomicrographs, or on dimensional measurement limits determined in accordance with Test Method F269.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 290 : 1994 : R2020 | Standard Specification for Round Wire for Winding Electron Tube Grid Laterals (Withdrawn 2024) |
| ASTM F 205 : 1994 : R2020 | Standard Test Method for Measuring Diameter of Fine Wire by Weighing (Withdrawn 2023) |
| ASTM F 204 : 1976 : R2018 | Standard Test Method for Surface Flaws in Tungsten Seal Rod and Wire |
| ASTM F 219 : 1996 | Standard Test Methods of Testing Fine Round and Flat Wire for Electron Devices and Lamps |
| ASTM F 16 : 2012 : R2022 | Standard Test Methods for Measuring Diameter or Thickness of Wire and Ribbon for Electronic Devices and Lamps (Withdrawn 2023) |
| ASTM F 16 : 2012 : R2017 | Standard Test Methods for Measuring Diameter or Thickness of Wire and Ribbon for Electronic Devices and Lamps |
| ASTM F 219 : 1996 : R2018 | Standard Test Methods of Testing Fine Round and Flat Wire for Electron Devices and Lamps (Withdrawn 2023) |
| ASTM F 269 : 1960 : R1996 : EDT 1 | Standard Test Method for Sag of Tungsten Wire |
| ASTM F 269 : 1960 : R2019 | Standard Test Method for Sag of Tungsten Wire |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.