• Shopping Cart
    There are no items in your cart

ASTM F 3006 : 2019

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Specification for Ball Drop Impact Resistance of Laminated Architectural Flat Glazing

Available format(s)

Hardcopy , PDF

Superseded date

29-01-2020

Superseded by

ASTM F 3006 : 2020

Language(s)

English

Published date

15-04-2019

€59.22
Excluding VAT

This specification covers the destructive ball drop testing of laminated flat glass products intended for use in architectural glazing applications.

Committee
F 12
DocumentType
Standard
Pages
3
ProductNote
This standard is also refers to CPSC 16 CFR 1201,GANA LD-100-06
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This specification covers the destructive ball drop testing of laminated flat glass products intended for use in architectural glazing applications.

1.2This specification is intended for use as an in-plant quality control test to evaluate the impact performance of laminated flat glass when a 2.3 kg, 83 mm diameter smooth solid steel ball is dropped from a specified height.

1.3This specification does not yield data that is a substitute for safety glazing test requirements of ANSI Z97.1 or CPSC 16 CFR 1201. Qualification under this specification provides a basis for judgment of the ability of specimens to withstand the appropriate shot-bag impact. This specification provides a mechanism to allow fabricators a less cumbersome and lower cost method for the evaluation of impact performance that may be performed on a frequent basis while reducing the amount of waste materials generated from traditional impact tests.

1.4This specification is applicable to symmetrical and asymmetrical annealed, heat-strengthened, chemically strengthened, fully tempered laminated architectural flat glass including but not limited to: float, patterned, sheet, sand-blasted, grooved, and fritted.

1.5The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 4 on Hazards.

1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM C 1036 : 2001 Standard Specification for Flat Glass
ASTM C 1172 : 2009 : EDT 1 Standard Specification for Laminated Architectural Flat Glass
ASTM C 1048 : 1997 : REV B Standard Specification for Heat-Treated Flat Glass--Kind HS, Kind FT Coated and Uncoated Glass
ASTM C 1036 : 2006 Standard Specification for Flat Glass
ASTM C 1048 : 2018 Standard Specification for Heat-Strengthened and Fully Tempered Flat Glass
ASTM C 1172 : 2003 Standard Specification for Laminated Architectural Flat Glass
ASTM C 1036 : 2016 Standard Specification for Flat Glass
ASTM C 1036 : 2011 Standard Specification for Flat Glass
ASTM C 1048 : 2012 Standard Specification for Heat-Strengthened and Fully Tempered Flat Glass
ASTM F 3007 : 2019 Standard Test Method for Ball Drop Impact Resistance of Laminated Architectural Flat Glass
ASTM C 1172 : 2009 Standard Specification for Laminated Architectural Flat Glass
ASTM F 3007 : 2013 Standard Test Method for Ball Drop Impact Resistance of Laminated Architectural Flat Glass
ASTM C 1048 : 2004 Standard Specification for Heat-Treated Flat Glass—Kind HS, Kind FT Coated and Uncoated Glass
ASTM C 1172 : 2014 Standard Specification for Laminated Architectural Flat Glass
ASTM C 1036 : 2011 : EDT 1 Standard Specification for Flat Glass
ASTM C 1048 : 2012 : EDT 1 Standard Specification for Heat-Strengthened and Fully Tempered Flat Glass
ASTM C 1036 : 1991 : R1997 Standard Specification for Flat Glass
ASTM C 1172 : 2019 Standard Specification for Laminated Architectural Flat Glass
ASTM C 1172 : 1996 : EDT 1 Standard Specification for Laminated Architectural Flat Glass

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.