ASTM F 3087 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Acrylic Molding Resins for Medical Implant Applications
Hardcopy , PDF
23-09-2024
English
15-07-2015
CONTAINED IN VOL. 13.02, 2015 Defines acrylic resins supplied in virgin form (typically pellets, powder, or granules) for medical implant applications.
Committee |
F 04
|
DocumentType |
Standard
|
Pages |
5
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1This specification covers acrylic resins supplied in virgin form (typically pellets, powder, or granules) for medical implant applications. The co-polymers are limited to random co-polymers. This specification provides requirements and associated test methods for this thermoplastic when it is intended for use in manufacturing implantable medical devices or components of medical devices.
1.1.1While a variety of co-monomers may be used, the composition of the resin shall contain poly(methyl methacrylate) (PMMA) as its primary ingredient. Classification D788 defines an acrylic molding compound as “having at least 70% of the polymer polymerized from methyl methacrylate.” The terms PMMA and acrylic as used herein refer generically to both the homopolymer and to co-polymers as defined above.
1.2As with any material, some characteristics may be altered by the processing techniques (such as molding, extrusion, machining, sterilization, and so forth) required for the production of a specific part or device. Therefore, properties of fabricated forms of this resin should be evaluated using test methods that are appropriate to ensure safety and efficacy as agreed upon between the supplier, purchaser, and regulating bodies.
1.3This specification allows for designation of acrylic resins for all medical implant applications. The actual extent of performance and suitability for a specific application shall be evaluated by the medical device manufacturer and regulating bodies.
1.4The properties included in this specification are those applicable for both unfilled acrylic polymers and for formulated resins containing barium sulfate. Indicated properties (Table 1 and Table X3.1) are for unfilled injection molded forms. Forms containing fillers other than barium sulfate, colorants, polymer blends that contain PMMA, or reclaimed materials are not covered by this specification.
1.5Compliance with this specification does not obviate the need for functional testing of any device fabricated from the resin to demonstrate effectiveness in its intended application.
1.6The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D 1238 : 2000 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
ASTM D 1238 : 2004 : REV C | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 1238 : 2023 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 1238 : 2023 : REV A | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 1238 : 2013 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 788 : 2016 : REDLINE | Standard Classification System for Poly(Methyl Methacrylate) (PMMA) Molding and Extrusion Compounds |
ASTM D 1238 : 2010 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 1238 : 2013 : REDLINE | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM F 451 : 2016 | Standard Specification for Acrylic Bone Cement |
ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
ASTM F 451 : 2021 | Standard Specification for Acrylic Bone Cement |
ASTM D 1898 : 1968 : R1989 | Standard Practice for Sampling of Plastics (Withdrawn 1998) |
ASTM D 638 : 2014 | Standard Test Method for Tensile Properties of Plastics |
ASTM D 1238 : 2004 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM F 748 : 2016 : REDLINE | Standard Practice for Selecting Generic Biological Test Methods for Materials and Devices |
ISO 10993-1:2009 | Biological evaluation of medical devices Part 1: Evaluation and testing within a risk management process |
ASTM D 695 : 2015 | Standard Test Method for Compressive Properties of Rigid Plastics |
ASTM D 1238 : 2001 : EDT 1 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 695 : 2015 : REDLINE | Standard Test Method for Compressive Properties of Rigid Plastics |
ASTM D 1238 : 2020 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 1238 : 2004 : REV A | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 695 : 2023 | Standard Test Method for Compressive Properties of Rigid Plastics |
ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
ASTM D 1238 : 1985 | Standard Test Method for Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 638 : 2022 | Standard Test Method for Tensile Properties of Plastics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.