• Shopping Cart
    There are no items in your cart

ASTM F 585 : 2016 : R2021

Current

Current

The latest, up-to-date edition.

Standard Guide for Insertion of Flexible Polyethylene Pipe Into Existing Sewers

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

08-04-2021

€56.53
Excluding VAT

Committee
F 17
DocumentType
Guide
Pages
9
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

1.1This guide describes design and selection considerations and installation procedures for the rehabilitation of sanitary and storm sewers by the insertion of solid wall or profile wall or corrugated polyethylene pipe into an existing pipe and along its existing line and grade. The procedures in this guide are intended to minimize traffic disruption, surface damage, surface restoration and interruption of service.

1.2The polyethylene piping product manufacturer should be consulted to determine the polyethylene piping product’s suitability for insertion renewal as described in this guide.

1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See 6.1, 7.1, and 8.1 for additional safety precautions.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM F 3371 : 2019 Standard Specification for Polyolefin Pipe and Fittings for Drainage, Waste, and Vent Applications
ASTM F 2896 : 2011 : R2017 Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids
ASTM F 714 : 2021 Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter
ASTM F 894 : 2019 Standard Specification for Polyethylene (PE) Large Diameter Profile Wall Sewer and Drain Pipe

ASTM F 2620 : 2024 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM F 412 : 2024 Standard Terminology Relating to Plastic Piping Systems
ASTM F 412 : 2020 : REV A Standard Terminology Relating to Plastic Piping Systems
ASTM F 412 : 2021 Standard Terminology Relating to Plastic Piping Systems
ASTM F 2620 : 2020 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM F 1804 : 2008 : R2020 Standard Practice for Determining Allowable Tensile Load for Polyethylene (PE) Gas Pipe During Pull-In Installation
ASTM F 412 : 2024 : REV A Standard Terminology Relating to Plastic Piping Systems
ASTM F 2620 : 2020 : REV A : EDT 1 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM F 1417 : 2011 : REV A : R2019 : EDT 1 Standard Practice for Installation Acceptance of Plastic Non-pressure Sewer Lines Using Low-Pressure Air
ASTM F 412 : 2023 Standard Terminology Relating to Plastic Piping Systems
ASTM F 1417 : 2011 : REV A : R2024 Standard Practice for Installation Acceptance of Plastic Non-pressure Sewer Lines Using Low-Pressure Air
ASTM F 2620 : 2020 : REV A Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM F 2620 : 2020 : REV A : EDT 2 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM F 1804 : 2021 Standard Practice for Determining Allowable Tensile Load for Polyethylene (PE) Gas Pipe During Pull-In Installation

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.