ASTM F 606/F606M : 2021 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
18-11-2024
English
01-06-2021
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
F 16
|
| DocumentType |
Redline
|
| Pages |
19
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1These test methods cover establishment of procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers, direct tension indicators, and rivets.
1.2Property requirements and the applicable tests for their determination are specified in individual product standards. In those instances where the testing requirements are unique or at variance with these standard procedures, the product standard shall specify the controlling testing requirements. In the absence of any specified test requirement(s), these test methods shall apply.
1.3These test methods describe mechanical tests for determining the following properties:
| Section | |
| For Externally Threaded Fasteners: | 3 |
| Product Hardness | 3.1 |
| Proof Load | 3.2.1 |
| Method 1, Length Measurement | 3.2.3 |
| Method 2, Yield Strength | 3.2.4 |
| Method 3, Uniform Hardness | 3.2.5 |
| Axial Tension Testing of Full-Size Product | 3.4 |
| Wedge Tension Testing of Full-Size Product | 3.5 |
| Tension Testing of Machined Test Specimens | 3.6 |
| Total Extension at Fracture Test | 3.7 |
| For Internally Threaded Fasteners: | 4 |
| Product Hardness | 4.1 |
| Proof Load Test | 4.2 |
| Cone Proof Load Test | 4.3 |
| For Washers and Direct Tension Indicators: | 5 |
| Product Hardness-General Requirements | 5.1 |
| Through Hardened Washers | 5.2 |
| Carburized Washers | 5.3 |
| Stainless Steel and Nonferrous Washers | 5.4 |
| Direct Tension Indicators | 5.5 |
| Compression Load | 5.6 |
| For Rivets: | 6 |
| Product Hardness | 6.1 |
| Test for Embrittlement of Metallic-Coated Externally Threaded Fasteners | 7 |
| Test Method for Determining Decarburization and Carburization | 8 |
1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
Note 1:The values are stated in inch-pound for inch fasteners and SI metric units for metric fasteners.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.