• There are no items in your cart

ASTM F 679 : 2021

Withdrawn

Withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

Standard Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings (Withdrawn 2024)

Available format(s)

Hardcopy , PDF

Withdrawn date

10-01-2022

Language(s)

English

Published date

01-11-2021

€67.30
Excluding VAT

Committee
F 17
DocumentType
Standard
Pages
7
PublisherName
American Society for Testing and Materials
Status
Withdrawn
Supersedes

1.1This specification covers requirements and test methods for materials, dimensions, workmanship, flattening resistance, impact resistance, pipe stiffness, extrusion quality, joining system, and a form of marking for large diameters, 18 to 60 in. poly(vinyl chloride) (PVC) sewer pipe and fittings with integral bell elastomeric seal joints or solvent cemented sockets.

1.2The requirements of this specification are intended to provide pipe and fittings suitable for nonpressure drainage of sewage and surface water. Pipe and fittings produced to this specification should be installed in accordance with Practice D2321.

Note 1:Industrial waste disposal lines should be installed only with the specific approval of the governing code authority since temperatures in excess of 140 °F (60 °C) and chemicals not commonly found in drains and sewers may be encountered.

1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4The following precautionary caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM F 794 : 2021 Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter
ASTM F 2946 : 2012 : R2021 Standard Specification for PVC Hub and Elastomeric Seal (Gasket) Tee Connection for Joining Plastic Pipe to Insitu Pipelines and Manholes
ASTM F 949 : 2020 Standard Specification for Poly(Vinyl Chloride) (PVC) Corrugated Sewer Pipe With a Smooth Interior and Fittings
ASTM F 1336 : 2020 Standard Specification for Poly(Vinyl Chloride) (PVC) Gasketed Sewer Fittings
ASTM F 1803 : 2015 : R2019 Standard Specification for Poly (Vinyl Chloride)(PVC) Closed Profile Gravity Pipe and Fittings Based on Controlled Inside Diameter
ASTM F 3533/F3533M : 2023 Standard Guide for Inspection and Acceptance of Installed Thermoplastic Storm and Sanitary Sewer Pipe

ASTM F 412 : 2021 Standard Terminology Relating to Plastic Piping Systems
ASTM D 3212 : 2020 Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
ASTM D 2152 : 2023 Standard Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by Acetone Immersion
ASTM D 2122 : 2022 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 1600 : 2018 Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
ASTM D 3212 : 2021 Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
ASTM F 412 : 2023 Standard Terminology Relating to Plastic Piping Systems
ASTM D 2152 : 2017 Standard Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by Acetone Immersion
ASTM D 2122 : 2016 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.