ASTM F 914 : 2003
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Acoustic Emission for Insulated and Non-Insulated Aerial Personnel Devices Without Supplemental Load Handling Attachments
Hardcopy , PDF
11-11-2014
English
10-09-2003
CONTAINED IN VOL. 10.03, 2009 Defines a procedure for nondestructive testing using acoustic emission (AE) testing for insulated and non-insulated aerial personnel devices which do not have a supplemental load handling attachment.
Committee |
F 18
|
DocumentType |
Test Method
|
Pages |
9
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1 This test method describes a procedure for non-destructive testing using acoustic emission (AE) testing for insulated and non-insulated aerial personnel devices which do not have a supplemental load handling attachment.
1.1.1 Equipment Covered—This test method covers the following types of vehicle-mounted insulated aerial personnel devices:
1.1.1.1 Extensible boom aerial personnel devices,
1.1.1.2 Articulating boom aerial personnel devices, and
1.1.1.3 Any combination of 1.1.1.1 and 1.1.1.2.
1.1.2 Equipment Not Covered—This test method does not cover any of the following equipment:
Material-handling aerial devices,
Digger-derricks with platform, and
Cranes with platform.
1.2 The AE test method is used to detect and area-locate emission sources. Verification of emission sources may require the use of other nondestructive test (NDT) methods, such as radiography, ultrasonics, magnetic particle, liquid penetrant, and visual inspection. Warning—This test method requires that external loads be applied to the superstructure of the vehicle under test. During the test, caution must be taken to safeguard personnel and equipment against unexpected failure or instability of the vehicle or components.
Note 1—This test method is not intended to be a stand alone NDT method for the verification of the structural integrity of an aerial device. Other NDT methods should be used to supplement the results.
1.3 The values given in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM F 1430/F1430M : 2018 : REDLINE | Standard Test Method for Acoustic Emission Testing of Insulated and Non-Insulated Aerial Personnel Devices with Supplemental Load Handling Attachments |
IEEE DRAFT 1307 : D8B 96 | ANSI/IEEE DRAFT TRIAL GUIDE FOR FALL PROTECTION FOR THE USE UTILITY INDUSTRY |
ASTM F 1430 : 2003 | Standard Test Method for Acoustic Emission Testing of Insulated and Non-Insulated Aerial Personnel Devices with Supplemental Load Handling Attachments |
ASTM F 1797 : 2018 : REDLINE | Standard Test Method for Acoustic Emission Testing of Insulated and Non-Insulated Digger Derricks |
14/30318963 DC : DRAFT DEC 2014 | BS EN 61057 - LIVE WORKING - INSULATING AERIAL DEVICES FOR MOUNTING ON A CHASSIS |
I.S. EN 61057:2017 | LIVE WORKING - INSULATING AERIAL DEVICES FOR MOUNTING ON A CHASSIS |
EN 61057:2017 | Live working - Insulating aerial devices for mounting on a chassis |
ASTM F 1430 : 2003 : EDT 1 | Standard Test Method for Acoustic Emission Testing of Insulated and Non-Insulated Aerial Personnel Devices with Supplemental Load Handling Attachments |
ACI 437.1R : 2007 | LOAD TESTS OF CONCRETE STRUCTURES: METHODS, MAGNITUDE, PROTOCOLS & ACCEPTANCE CRITERIA |
IEEE 1307-2004 | IEEE Standard for Fall Protection for Utility Work |
BS EN 61057:1994 | Aerial devices with insulating boom used for live working exceeding 1 kV a.c. |
IEC 61057:2017 | Live working - Insulating aerial devices for mounting on a chassis |
ASNT SNT TC 1A : 2016 | TOPICAL OUTLINES FOR QUALIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL |
ASTM E 750 : 2015 : REDLINE | Standard Practice for Characterizing Acoustic Emission Instrumentation |
ASTM E 650 : 1997 | Standard Guide for Mounting Piezoelectric Acoustic Emission Sensors |
ASTM E 976 : 2015 : REDLINE | Standard Guide for Determining the Reproducibility of Acoustic Emission Sensor Response |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.