AWS C3.5 : 1999

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View superseded by

SPECIFICATION FOR INDUCTION BRAZING

Available format(s):

Superseded date: 23-07-2013

Language(s):

Published date: 12-01-2013

Publisher: American Welding Society

Table of Contents - (Show below) - (Hide below)

Personnel
Foreword
1. Scope
2. Applicable Documents
3. Classification of Brazed Joints
3.1 Method of Classification
3.2 Class A Joints
3.3 Class B Joints
3.4 Class C Joints
3.5 No Class Specified
4. Process Requirements
4.1 Process Description
4.2 Equipment
4.3 Materials
4.4 Procedure requirements
4.5 Qualification
5. Quality Assurance Provisions
5.1 Responsibility for Inspection
5.2 Requirements for Compliance
5.3 Sequence of Inspection and Manufacturing Operations
5.4 Required Inspections of Brazed Joints
5.5 Acceptance Criteria
5.6 Process Completion
6. Definitions
Annex A - Guidelines for Preparation of Technical Inquiries
for AWS Technical Committees
A1. Introduction
A2. Procedure
A3. Interpretation of Provisions of the Standard
A4. Publication of Interpretations
A5. Telephone Inquiries
A6. The AWS Technical Committee
AWS Brazing and Soldering Documents

Abstract - (Show below) - (Hide below)

Defines minimum fabrication and quality requirements for the induction brazing of materials such as steel, copper, copper alloys, and heat and corrosion resistant alloys. Standardizes induction brazing process requirements and control braze joint quality for all applications where braze joints of assured quality are necessary.

General Product Information - (Show below) - (Hide below)

Development Note	Supersedes MIL B 007883. (06/2004)
Document Type	Standard
ISBN
Pages
Published
Publisher	American Welding Society
Status	Superseded
Superseded By	AWS C3.5M/C3.5 : 2016 AWS C3.5M/C3.5 : 2007
Supersedes	MIL-B-007883 Revision C:1968 MIL-B-7883 Revision B:1968

Standards Referenced By This Book - (Show below) - (Hide below)

MS27225 Revision C:2007	Nipple Assembly 45 Degrees, Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines
AWS BRH:2007	BRAZING HANDBOOK
AWS SHB : 3	SOLDERING HANDBOOK
AWS WHC1.10 : 0	WELDING SCIENCE AND TECHNOLOGY, WELDING HANDBOOK, 9TH ED., VOL 1 - CHAPTER 10: MONITORING AND CONTROL OF WELDING AND JOINING PROCESSES
MIL-STD-2088 Revision B:2007	BOMB RACK UNIT (BRU), SINGLE STORE, AIRCRAFT
IPC A 630 CHINESE : -	ACCEPTABILITY STANDARD FOR MANUFACTURE, INSPECTION AND TESTING OF ELECTRONIC ENCLOSURES
MIL STD 11991 : A	GENERAL STANDARD FOR PARTS, MATERIALS, AND PROCESSES
MIL-HDBK-510 Revision A:2014	AEROSPACE FUELS CERTIFICATION
MIL-G-18997 Revision E:1991	GAUGE, PRESSURE, DIAL INDICATING
MIL-HDBK-115 Revision C:2016	U.S. ARMY REVERSE ENGINEERING HANDBOOK (GUIDELINES AND PROCEDURES)
AWS C3.8 : 90(R1998)	RECOMMENDED PRACTICES FOR ULTRASONIC INSPECTION OF BRAZED JOINTS
MIL-HDBK-510-1 Revision A:2010	AEROSPACE FUELS CERTIFICATION
NASA SSTD 8070 0074 : 2015	REFRIGERANT TUBING SYSTEM
NASA STD 6016(INT) : 2006	STANDARD MATERIALS AND PROCESSES REQUIREMENTS FOR SPACECRAFT
NASA STD 5005(INT) : 2007	THE DESIGN AND FABRICATION OF GROUND SUPPORT EQUIPMENT
IPC A 630 : 0	ACCEPTABILITY STANDARD FOR MANUFACTURE, INSPECTION AND TESTING OF ELECTRONIC ENCLOSURES
MIL-STD-186 Revision F:2002	PROTECTIVE FINISHING SYSTEMS FOR ROCKETS, GUIDED MISSILES, SUPPORT EQUIPMENT AND RELATED MATERIALS
JSSG-2010-12 Base Document:1998	Crew Systems Deployable Aerodynamic Decelerator (DAD) Systems Handbook
SAE AS 12500 : 2018	CORROSION PREVENTION AND DETERIORATION CONTROL IN ELECTRONIC COMPONENTS AND ASSEMBLIES
MS27223 Revision C:2007	Nipple Assembly 90 Degrees, Adapter, Hose to Tube, Reusable, Hydraulic, Fuel and Oil Lines 1/4 Inch through 2 Inch Tube Sizes

Standards Referencing This Book - (Show below) - (Hide below)

SAE AMS 2424 : 2010	PLATING, NICKEL LOW-STRESSED DEPOSIT
AWS A5.31 : 1992	SPECIFICATION FOR FLUXES FOR BRAZING AND BRAZE WELDING
SAE AMS 2404 : 2013	PLATING, ELECTROLESS NICKEL
AWS A2.4 : 2012	STANDARD SYMBOLS FOR WELDING, BRAZING, AND NONDESTRUCTIVE EXAMINATION
ANSI/NCSL Z540 1 : 94(R2002)	CALIBRATION - CALIBRATION LABORATORIES AND MEASURING AND TEST EQUIPMENT - GENERAL REQUIREMENTS
AWS A3.0 : 0	STANDARD WELDING TERMS AND DEFINITIONS - INCLUDING TERMS FOR ADHESIVE BONDING, BRAZING, SOLDERING, THERMAL CUTTING, AND THERMAL SPRAYING
AWS BRH:2007	BRAZING HANDBOOK
SAE AMS 2403 : 2015	PLATING, NICKEL, GENERAL PURPOSE
AWS B2.2 : 1991	STANDARD FOR BRAZING PROCEDURE AND PERFORMANCE QUALIFICATION
AWS C3.8 : 90(R1998)	RECOMMENDED PRACTICES FOR ULTRASONIC INSPECTION OF BRAZED JOINTS
AWS A5.8 : 1992	FILLER METALS FOR BRAZING AND BRAZE WELDING, SPECIFICATION FOR

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart