AWWA M55 : 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PE PIPE - DESIGN AND INSTALLATION
07-03-2022
23-07-2013
List of Terms and Equation Symbols
List of Conversions
Preface
Acknowledgments
Chapter 1 - Engineering Properties of Polyethylene
Chapter 2 - Manufacturing, Testing, and Inspection
Chapter 3 - Hydraulics of PE Pipe
Chapter 4 - Working Pressure Rating
Chapter 5 - External Load Design
Chapter 6 - Joining and Fittings
Chapter 7 - Transportation, Handling, and Storage of Pipe
and Fittings
Chapter 8 - Installation
Chapter 9 - Hydrotesting and Commissioning
Chapter 10 - Maintenance and Repairs
Index
AWWA Manuals
Specifies HDPE pipe and fittings products and certain appurtenances, and their applications to practical installations, whether of a standard or special nature.
| DocumentType |
Standard
|
| PublisherName |
American Water Works Association
|
| Status |
Superseded
|
| SupersededBy |
| AWWA M27 : 3 | EXTERNAL CORROSION CONTROL FOR INFRASTRUCTURE SUSTAINABILITY |
| ASTM F 2880 : 2014 : REDLINE | Standard Specification for Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes <fraction><num>3/4</den></fraction > in. to 65 in. |
| AWWA C901 : 2017 | POLYETHYLENE (PE) PRESSURE PIPE AND TUBING, 3/4 IN. (19 MM) THROUGH 3 IN. (76 MM), FOR WATER SERVICE |
| AWWA C906:2015 | POLYETHYLENE (PE) PRESSURE PIPE AND FITTINGS, 4 IN. THROUGH 65 IN. (100 MM THROUGH 1,650 MM), FOR WATERWORKS |
| AWWA M68 : 2017 | WATER QUALITY IN DISTRIBUTION SYSTEMS |
| FM 1613 : 2017 | POLYETHYLENE (PE) PIPE AND FITTINGS FOR UNDERGROUND FIRE PROTECTION SERVICE |
| AWWA C153/A21.53 : 2011 | DUCTILE-IRON COMPACT FITTINGS |
| NSF 61 : 2016 | DRINKING WATER SYSTEM COMPONENTS - HEALTH EFFECTS |
| AWWA C207 : 2013 | STEEL PIPE FLANGES FOR WATERWORKS SERVICE, SIZES 4 IN. THROUGH 144 IN. (100 MM THROUGH 3,600 MM) |
| ASTM D 3261 : 2016-11 | SPECIFICATION FOR BUTT HEAT FUSION POLYETHYLENE (PE) PLASTIC FITTINGS FOR POLYETHYLENE (PE) PLASTIC PIPE AND TUBING |
| ASTM D 2774 : 2012 : REDLINE | Standard Practice for Underground Installation of Thermoplastic Pressure Piping |
| ASTM D 1238 : 2013 : REDLINE | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| AWWA C906:2015 | POLYETHYLENE (PE) PRESSURE PIPE AND FITTINGS, 4 IN. THROUGH 65 IN. (100 MM THROUGH 1,650 MM), FOR WATERWORKS |
| PPI TR 3 : 2017 | POLICIES AND PROCEDURES FOR DEVELOPING HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESSES (HDS), PRESSURE DESIGN BASIS (PDB), STRENGTH DESIGN BASIS (SDB), MINIMUM REQUIRED STRENGTH (MRS) RATINGS, AND CATEGORIZED REQUIRED STRENGTH (CRS) FOR THERMOPLASTIC PIPING MATERIALS OR PIPE |
| PPI TR 4 : 2017 | HDB/HDS/SDB/PDB/MRS LISTED MATERIALS - PPI LISTING OF HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESS (HDS), STRENGTH DESIGN BASIS (SDB), PRESSURE DESIGN BASIS (PDB) AND MINIMUM REQUIRED STRENGTH (MRS) RATINGS FOR THERMOPLASTIC PIPING MATERIALS OR PIPE |
| ASTM D 698 : 2013-05 | TEST METHODS FOR LABORATORY COMPACTION CHARACTERISTICS OF SOIL USING STANDARD EFFORT (12400 FT-LBF/FT[3] (600 KN-M/M[3])) |
| ASTM F 1962 : 2011 : REDLINE | Standard Guide for Use of Maxi-Horizontal Directional Drilling for Placement of Polyethylene Pipe or Conduit Under Obstacles, Including River Crossings |
| AWWA C901 : 2017 | POLYETHYLENE (PE) PRESSURE PIPE AND TUBING, 3/4 IN. (19 MM) THROUGH 3 IN. (76 MM), FOR WATER SERVICE |
| ASTM D 790 : 2017 : REDLINE | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
| AWWA C110/A21.10 : 2012 | DUCTILE-IRON AND GRAY-IRON FITTINGS |
| PPI TR 19 : 2007 | CHEMICAL RESISTANCE OF THERMOPLASTICS PIPING MATERIALS |
| ASTM D 2122 : 2016 : REDLINE | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
| ASTM D 3350 : 2014 : REDLINE | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 695 : 2015 : REDLINE | Standard Test Method for Compressive Properties of Rigid Plastics |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
| ASTM D 1693 : 2015 : REDLINE | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| AWWA C651 : 2014 | DISINFECTING WATER MAINS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.