BS 2X 33:1998
Current
The latest, up-to-date edition.
Specification for two component epoxy primer for aerospace purposes
Hardcopy , PDF
English
16-11-2005
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Committees responsible
Foreword
1 Scope
2 Normative references
3 Definitions
4 Materials
5 Performance
6 Batch inspection
7 Marking
Annex A (normative) Type approval
Annex B (normative) Preparation of test panels
List of references
Defines requirements for the materials and performance of two types of strontium chromate pigmented two pack resin based primer, for air-drying at ambient temperature, for aerospace applications.
| Committee |
ACE/65
|
| DevelopmentNote |
Supersedes 96/705059 DC and BS X33(1991) (07/2005) Reviewed and confirmed by BSI, December 2009. (11/2009)
|
| DocumentType |
Standard
|
| Pages |
12
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
This British standard specifies requirements for the materials and performance of two types of strontium chromate pigmented two pack �®I resin based primer, for air-drying at ambient temperature, for aerospace applications.
Type A materials are intended for application to chemically pretreated substrates (e.g. by a chromate conversion process) suitable for general applications.
Type B materials are similar to type A but with improved tolerance to the standard of surface preparation, and with increased chemical resistance.
The primers are for use on metallic substrates as an anti-corrosive coating on interior surfaces, or, when overcoated with a compatible finish, as a protective and decorative finishing scheme for exterior surfaces.
Information on application for type approval is provided in Annex A.
| DEFSTAN 03-4/5(2006) : 2006 | THE PRE-TREATMENT AND PROTECTION OF STEEL ITEMS OF MAXIMUM TENSILE STRENGTH EXCEEDING 1450 MPA |
| DEFSTAN 80-16/4(2006) : 2006 | PAINT REMOVER, DICHLOROMETHANE, WATER RINSABLE TYPE - TYPE 1: HIGH VISCOSITY (BRUSHING) TYPE 2: LOW VISCOSITY (SPRAYING) |
| DEFSTAN 00-970(PT0)/9(2012) : 2012 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 79-18/2(2001) : 2001 | CLEANING FLUID FOR COMPRESSORS OF GAS TURBINE ENGINES |
| DEFSTAN 00-970(PT0)/17(2016) : 2016 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/7(2011) : 2011 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 80-164/3(2009) : 2009 | PAINT, SYSTEM, FLUORESCENT |
| DEFSTAN 00-970(PT0)/14(2014) : 2014 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 80-214/3(2009) : 2009 | PAINT, FINISH, SELECTIVELY STRIPPABLE, ACRYLIC - TYPES: BRUSHING, SPRAYING |
| DEFSTAN 00-970(PT0)/15(2015) : 2015 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/12(2014) : 2014 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/11(2013) : 2013 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 05-133(PT1)/1(2011) : 2011 | METHODS FOR TESTING PAINTS, CHEMICALS AND ASSOCIATED PRODUCTS - PART 1: PAINTS AND ALLIED PRODUCTS |
| DEFSTAN 00-970(PT0)/13(2014) : 2014 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 07-85(PT1)/3(2006) : 2006 | DESIGN REQUIREMENTS FOR WEAPONS AND ASSOCIATED SYSTEMS - PART 1: MANDATORY DESIGN REQUIREMENTS |
| DEFSTAN 80-158/4(2010) : 2010 | PAINT, FINISH, EROSION RESISTING FOR AIRCRAFT, POLYURETHANE, MULTI-PACK, VOC COMPLIANT |
| DEFSTAN 03-4/6(2011) : 2011 | THE PRE-TREATMENT AND PROTECTION OF STEEL ITEMS OF SPECIFIED MAXIMUM TENSILE STRENGTH EXCEEDING 1450 MPA |
| DEFSTAN 00-970(PT0)/8(2011) : 2011 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/16(2015) : 2015 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 80-14/2(2006) : 2006 | PAINT REMOVER, DICHLOROMETHANE, WATER RINSABLE NON AEROSPACE USE TYPE: BRUSHING |
| DEFSTAN 80-221/1(2009) : 2009 | PAINT REMOVER FOR AIR DRYING PAINT SCHEME FOR AEROSPACE PURPOSES - TYPE 1: HIGH VISCOSITY (BRUSHING) - TYPE 2: LOW VISCOSITY (SPRAYING) |
| DEFSTAN 80-158/3(2004) : 2004 | PAINT SYSTEM, EROSION RESISTING FOR AIRCRAFT, POLYURETHANE, MULTI-PACK, VOC COMPLIANT |
| DEFSTAN 80-212/2(2006) : 2006 | PAINT, FINISHING, POLYURETHANE, ABRASION RESISTING, LOW VOC, MULTI-PACK |
| DEFSTAN 00-970(PT0)/10(2013) : 2013 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| BS 2X 34:1998 | Specification for two component polyurethane finish for aerospace purposes |
| BS X 35:1998 | Specification for selectively removable intermediate coating for aerospace purposes |
| SAE AMS03_4A | The Pre-Treatment and Protection of Steel Items of Specified Maximum Tensile Strength Exceeding 1450 MPa |
| SAE AMS03_18A | Chromate Conversion Coatings (Chromate Filming Treatments) Grades: Standard and Brushing for Aluminum and Aluminum Alloys |
| BS X 36:1998 | Specification for paint remover for air drying selectively removable paint scheme for aerospace purposes |
| DEFSTAN 03-18/5(2012) : 2012 | CHROMATE CONVERSION COATINGS (CHROMATE FILMING TREATMENTS) GRADES: STANDARD AND BRUSHING FOR ALUMINIUM AND ALUMINIUM ALLOYS |
| 14/30290245 DC : 0 | BS 2X35:2003 + A1 - SELECTIVELY REMOVABLE INTERMEDIATE COATING FOR AEROSPACE PURPOSES |
| DEFSTAN 03-18/4(2008) : 2008 | CHROMATE CONVERSION COATINGS (CHROMATE FILMING TREATMENTS) GRADES: STANDARD AND BRUSHING FOR ALUMINIUM AND ALUMINIUM ALLOYS |
| BS 2X 32:1998 | Specification for pre-treatment etch primer for aerospace purposes |
| BS 2X 35(2003) : 2003 | SELECTIVELY REMOVABLE INTERMEDIATE COATING FOR AEROSPACE PURPOSES |
| BS EN 605:1992 | Paints and varnishes. Standard panels for testing |
| BS EN ISO 1513:1995 | Paints and varnishes. Examination and preparation of samples for testing |
| BS EN ISO 3696:1995 | Water for analytical laboratory use. Specification and test methods |
| BS 2X 34:1998 | Specification for two component polyurethane finish for aerospace purposes |
| BS EN 23270:1991 | Specification for temperatures and humidities for conditioning and testing paints, varnishes and their raw materials |
| BS EN ISO 2431:2011 | Paints and varnishes. Determination of flow time by use of flow cups |
| DEFSTAN 79-17/1(1994) : INTERIM | COMPOUND, CLEANING, FOAMING, FOR AIRCRAFT SURFACES |
| DEFSTAN 79-17/2(1998) : 1998 | COMPOUND, CLEANING, FOAMING, FOR AIRCRAFT SURFACES |
| BS EN ISO 1520:2006 | Paints and varnishes. Cupping test |
| BS EN 29117:1992 | Methods of test for paints. Tests associated with paint film formation Paints and varnishes. Determination of through-dry state and through-dry time. Method of test |
| BS L 163:1978 | Specification for sheet and strip of aluminium-coated aluminium-copper-magnesium-silicon-manganese alloy (solution treated, cold worked for flattening and aged at room temperature) (Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8) |
| BS EN 2395:2005 | Aerospace series. Aluminium alloy AL-P2014A-T4 or T42. Sheet and strip. 0,4 mm ≤a ≤6 mm |
| BS EN 2334:1997 | Chromic-sulphuric acid pickle of aluminium and aluminium alloys |
| BS 4313:1988 | Specification for strontium chromate pigments for paints |
| BS EN 3665:1997 | Test methods for paints and varnishes. Filiform corrosion resistance test on aluminium alloys |
| BS ISO 15710 : 2002 AMD 16861 | PAINTS AND VARNISHES - CORROSION TESTING BY ALTERNATE IMMERSION IN AND REMOVAL FROM A BUFFERED SODIUM CHLORIDE SOLUTION |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.