BS 3987:1991
Current
The latest, up-to-date edition.
Specification for anodic oxidation coatings on wrought aluminium for external architectural applications
Hardcopy , PDF
English
15-06-2001
Committees responsible
Foreword
Specification
1 Scope
2 Definitions
3 Visual inspection after anodizing
4 Colour
5 Thickness
6 Sealing
7 Surface abrasion resistance
Appendices
A Guidance on information to be supplied
B Guidance on properties affecting coating performance
C Choice of aluminium for anodizing
D Handling and temporary protection during
transportation and installation
E Maintenance of anodized aluminium
F Surface texture
G Visual inspection after anodizing
H Colour
J Examples of average and local thickness requirements
K Sealing quality: production control methods
L Guidance on sampling
Figure
1 Measuring points
Requirements for colour (where appropriate), coating thickness, sealing quality and abrasion resistance for clear and coloured coatings. Also gives guidance on handling and temporary protection during transportation and installation, maintenance and sampling.
Committee |
STI/33
|
DevelopmentNote |
Supersedes 00/121192 DC, 91/50611 DC and BS 3987(1974) (07/2005) Reviewed and confirmed by BSI, November 2012. (10/2012)
|
DocumentType |
Standard
|
Pages |
16
|
PublisherName |
British Standards Institution
|
Status |
Current
|
This British Standard specifies requirements for clear and coloured anodic oxidation coatings on wrought aluminium for external architectural applications. Guidance on the information to be supplied by the purchaser to the anodizer is given in Appendix A.
Guidance on properties affecting coating performance is given although reflectance and gloss are not specified (see Appendix B).
NOTE 1 The coatings consist mainly of aluminium oxide and are produced by an electrolytic oxidation process during which the aluminium acts as the anode.
NOTE 2 The composition of the aluminium is not specified but that used is assumed to be suitable for anodizing (see Appendix C).
NOTE 3 Temporary protection and maintenance of anodized aluminium after anodizing may be necessary (see Appendix D and Appendix E).
NOTE 4 The titles of the publications referred to in this standard are listed on the inside back cover.
BS 6000:1972 | Guide to the use of BS 6001, sampling procedures and tables for inspection by attributes |
BS EN 12373-7:2002 | Aluminium and aluminium alloys. Anodizing Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution with prior acid treatment |
BS EN 12373-5:1999 | Aluminium and aluminium alloys. Anodizing Assessment of quality of sealed anodic oxidation coatings by measurement of admittance |
BS 6161-18:1991 | Methods of test for anodic oxidation coatings on aluminium and its alloys Determination of surface abrasion resistance |
BS 6001-1:1991 | Sampling procedures for inspection by attributes Specification for sampling plans indexed by acceptable quality level (AQL) for lot-by-lot inspection |
BS EN 12373-10:1999 | Aluminium and aluminium alloys. Anodizing Measurement of mean specific abrasion resistance of anodic oxidation coatings using an abrasive jet test apparatus |
BS 4479-5:1990 | Design of articles that are to be coated Recommendations for anodic oxidation coatings |
BS 6002:1979 | Specification for sampling procedures and charts for inspection by variables for percent defective |
BS EN ISO 1463:2004 | Metallic and oxide coatings. Measurement of coating thickness. Microscopical method |
BS EN ISO 2360:2017 | Non-conductive coatings on non-magnetic electrically conductive base metals. Measurement of coating thickness. Amplitude-sensitive eddy-current method |
BS EN 12373-9:1999 | Aluminium and aluminium alloys. Anodizing Measurement of wear resistance and wear index of anodic oxidation coatings using an abrasive wheel wear test apparatus |
BS EN 12373-4:1998 | Aluminium and aluminium alloys. Anodizing Estimation of loss of absorptive power of anodic oxidation coatings after sealing by dye spot test with prior acid treatment |
BS EN 12373-8:1999 | Aluminium and aluminium alloys. Anodizing Determination of the comparative fastness to ultra-violet light and heat of coloured anodic oxidation coatings |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.