BS 4147:1980
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Specification for bitumen-based hot-applied coating materials for protecting iron and steel, including suitable primers where required
Hardcopy , PDF
29-12-2006
English
31-10-1980
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Cooperating organizations
Specification
Section one. General
1 Scope
2 References
3 Definitions
4 Types of bitumen-based coating material
5 Types of primer
Section two. Primers
6 Type A. Bitumen-based primer for cold application
7 Type B. Synthetic primer for cold application
8 Type C. Bitumen primer for hot application
Section three. Coating materials
9 Type 1. Unfilled coating materials
10 Type 2. Coating materials with inert non-fibrous
fillers
11 Type 3. Coating materials with inert fibrous fillers
Section four. Packaging, marking, sampling
12 Packaging
13 Marking
14 Sampling
15 Effect of non-metallic materials on water quality
Appendices
A Determination of volatile matter
B Determination of filler content by ignition
C Determination of density at 25 deg C
D Determination of penetration
E Sag test
F Bend test
G Impact test
H Peel tests
J Preparation of steel surfaces for the tests given in
appendices E to H
K Priming of steel surfaces for the tests given in
appendices E to H
L Application of coating material for the test given
in appendices E to H
M Recommendations on the use of coating materials
Tables
1 Characteristics of bitumen in type A primer
2 Characteristics of type A primer for cold
application
3 Characteristics of type B primer for cold
application
4 Characteristics of type 1 coating materials
5 Tests for type 1 coating materials
6 Characteristics of type 2 coating materials
7 Tests for type 2 coating materials
8 Characteristics of type 3 coating materials
9 Tests for type 3 coating materials
Figure
1 Mould for sample for density determination
Requirements for hot applied bitumen based materials, both unfilled and reinforced with inert powdered or fibrous fillers, which will provide protection against corrosion.
| Committee |
ISE/110
|
| DevelopmentNote |
Supersedes 77/13457 DC and 85/10042 DC (07/2005) Supersedes TS 10195A. (11/2005)
|
| DocumentType |
Standard
|
| Pages |
16
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| BS 2000-170(1982) : 1982 | METHODS OF TEST FOR PETROLEUM AND ITS PRODUCTS - FLASH POINT BY THE ABEL APPARATUS (NON STATUTORY METHOD) |
| BS 2000-47(1983) : 1983 | METHODS OF TEST FOR PETROLEUM AND ITS PRODUCTS - SOLUBILITY OF BITUMINOUS BINDERS |
| BS 4232:1967 | Specification for surface finish of blast-cleaned steel for painting |
| BS 2000-49(1983) : 1983 | METHODS OF TEST FOR PETROLEUM AND ITS PRODUCTS - PENETRATION OF BITUMINOUS MATERIALS |
| BS 3900-A6:1971 | Methods of test for paints. Tests on liquid paints (excluding chemical tests). Determination of flow time by use of flow cups |
| BS 3416:1975 | Specification for black bitumen coating solutions for cold application |
| BS 1796:1976 | Method for test sieving |
| BS 534:1966 | Specification for steel pipes, fittings and specials for water, gas and sewage |
| BS 4689:1980 | Method for determination of flash and fire points of petroleum products: Cleveland open cup method |
| BS 2000-58(1983) : 1983 | METHOD OF TEST FOR PETROLEUM AND ITS PRODUCTS - SOFTENING POINT OF BITUMEN (RING AND BALL) |
| BS CP2010-2(1970) : 1970 | PIPELINES - PART 2: DESIGN AND CONSTRUCTION OF STEEL PIPELINES IN LAND |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.