BS 4300-15(1973) : 1973
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS FOR GENERAL ENGINEERING PURPOSES (SUPPLEMENTARY SERIES) - 7020 BAR, EXTRUDED ROUND TUBE AND SECTIONS
Hardcopy , PDF
15-06-2001
BS EN 573-3:2013
BS EN 755-8:2016
BS EN 755-6:2008
BS EN 755-5:2008
BS EN 755-3:2008
BS EN 755-9:2016
BS EN 755-4:2008
BS EN 573-4:2004
BS EN 755-2:2016
BS EN 515:2017
BS EN 755-1:2016
BS EN 755-7:2016
English
01-01-1973
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Co-operating organizations
Foreword
Specification
1 General
1.1 Scope
1.2 Definitions
2 General requirements
2.1 General
2.2 Freedom from defects
2.3 Chemical composition
2.4 Condition
2.5 Sizes and tolerances
2.6 Selection of test samples
2.7 Mechanical tests
2.8 Retests
2.9 Certificate of compliance
2.10 Inspection
2.11 Independent test
2.12 Facilities for testing
2.13 The rounding of numbers rule
3 Specific requirements
3.1 Chemical composition
3.2 Mechanical properties
3.3 Tolerances
3.4 Normal radii for corners
Appendices
A Standard sizes of material
B Details of the international alloy designations
and chemical composition limits for wrought
aluminium alloys system
Tables
1 Heat-treatable materials; grouping into batches
2 Table deleted
3 Tensile test
4 Tolerances on diameter and length of round bar
intended for use on automatic lathes
5 Tolerances on width across flats of hexagonal bar
for nuts and bolts
6 Tolerances on length
7 Tolerances on width and diameter of bars and
regular sections
8 Tolerances on thickness of bars and regular
sections
9 Tolerances on open ends of channels and I-beams
10 Angular tolerances for extruded sections
11 Tolerances on wall thickness of extruded round
tube
12 Tolerances on outside diameter of extruded round
tube or on inside diameter of Class A and Class B
extruded round tubing
13 Tolerances on width or width across flats of
hollow sections
14 Tolerances on thickness of hollow sections
15 Tolerances on straightness for extruded bar,
regular sections and extruded round tube
16 Tolerances on twist for extruded solid and hollow
sections
17 Normal radii for corners
Figure
1 Tolerances on open ends of channels and I-beams
Describes aluminium alloy bar, extruded round tube and sections, including freedom from defects, chemical composition, condition, sizes and tolerances, selection of test samples, mechanical tests, retests, certificate of compliance, inspection, independent test, facilities for testing and the rounding of numbers rule.
| Committee |
NFM/35
|
| DocumentType |
Standard
|
| Pages |
26
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| BS 8118-2(1991) : 1991 | STRUCTURAL USE OF ALUMINIUM - PART 2: SPECIFICATION FOR MATERIALS, WORKMANSHIP AND PROTECTION |
| BS 3571-1:1985 | MIG welding Specification for MIG welding of aluminium and aluminium alloys |
| PD 6702-1:2009 | Structural use of aluminium Recommendations for the design of aluminium structures to BS EN 1999 |
| BS CP118(1969) : 1969 AMD 1129 | THE STRUCTURAL USE OF ALUMINIUM |
| BS 1161:1977 | Specification for aluminium alloy sections for structural purposes |
| BS 8118-1:1991 | Structural use of aluminium Code of practice for design |
| BS 2646-1:1993 | Autoclaves for sterilization in laboratories Specification for design, construction, safety and performance |
| BS 4229-1:1967 | Recommendations for metric sizes of non-ferrous and ferrous bars. Non-ferrous bars |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.