BS 4500-5:1988
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ISO limits and fits Specification for system of cone tolerances for conical workpieces from C = 1:3 to 1:500 and lengths from 6 mm to 630 mm
Hardcopy , PDF
30-09-2009
English
30-11-1988
Important note : Users cannot be edited or removed once added to your Multi user PDF.
National foreword
Committees responsible
Specification
1. Scope and field of application
2. Basis of the system
3. Definitions
4. Cone diameter tolerance TD
5. Cone angle tolerance AT
6. Cone form tolerances TF
7. Cone section diameter tolerance TDS
8. Table of cone angle tolerances
Annex
Maximum cone angle deviations resulting from the
cone diameter tolerances TD for 100 mm cone length
Figures
1. Cone
2. Conical workpiece - External cone
3. Conical workpiece - Internal cone
4. Basic cone
5. Actual cone
6. General definitions
7. Angles on cones
8. Limit cones, cone diameter, tolerance zone and
straightness of the generator tolerance zone
9. Cone diameter tolerance zone and roundness
tolerance zone
10. Limit cone angles
11. Acutal cone angles
12. Position of the cone angle within the cone diameter
tolerance zone
13. Cone diameter tolerance space formed by the cone
diameter tolerance
14. Admissible cone form deviation resulting from the
cone diameter tolerance
15. Admissible limit cone angles resulting from the cone
diameter tolerance
16. Variation of ATD within a range of cone length with
the limits of the length range L1 and L2
17. Cone section diameter tolerance TDS and cone angle
tolerance AT
18. Cone angle tolerance AT alpha of a cone defined by
its measuring diameter and the longitudinal
dimensions of which are defined themselves from the
position of the measuring plane
Specifies a system which applies to rigid workpieces for which the length of the generator can be considered as practically equal to the basic cone length.
| Committee |
TPR/1
|
| DevelopmentNote |
Also numbered as ISO 1947 Supersedes 88/71385 DC (08/2005)
|
| DocumentType |
Standard
|
| Pages |
16
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| BS 6607-3:1993 | Tool shanks with 7/24 taper for automatic tool changers Specification for tapers for spindle noses |
| BS 1660-10:1988 | Machine tapers Specification for drill chuck tapers (Jacob and short Morse) |
| BS 8888:2008 | Technical product specification. Specification |
| BS 341-1:1991 | Transportable gas container valves Specification for industrial valves for working pressures up to and including 300 bar |
| BS 341-3:2002 | Transportable gas container valves Valve outlet connections |
| BS 1660-4:1989 | Machine tapers Specification for spindle noses and tool shanks with self-release 7/24 tapers |
| BS 1660-1:1992 | Machine tapers Specification for shanks and sockets with self-holding tapers (Morse and metric 5%) |
| 11/30234091 DC : DRAFT JULY 2011 | BS 8888 - TECHNICAL PRODUCT DOCUMENTATION AND SPECIFICATION |
| DEFSTAN 02-304(PT1)/2(2002) : 2002 | SHAFTING SYSTEMS AND PROPULSORS - PART 1: DESIGN REQUIREMENTS FOR MAIN PROPULSION SHAFTING |
| BS 7333:1990 | Specification for slewing jib cranes |
| BS EN ISO 4566:1995 | Small craft with inboard engine. Propeller shaft ends and bosses with 1:10 taper |
| BS 8888:2004 | Technical product specification (TPS). Specification |
| BS 7161:1990 | Specification for propeller shaft ends and bosses for inboard-engined pleasure craft |
| DEFSTAN 02-304(PT2)/2(2002) : 2002 | SHAFTING SYSTEMS AND PROPULSORS - PART 2: DESIGN REQUIREMENTS FOR MAIN PROPULSION SHAFTING AUXILIARIES |
| BIP 3016 : 2004 | BS 8888(2004) - TECHNICAL PRODUCT SPECIFICATION CD-ROM |
| BS 8888:2006 | Technical product specification (TPS). Specification |
| BS 4500-4:1985 | ISO limits and fits Specification for system of cone (taper) fits for cones from <i>C</i>=1:3 to 1:500, lengths from 6 mm to 630 mm and diameters up to 500 mm |
| BS 308-3:1972 | Engineering drawing practice. Geometrical tolerancing |
| ISO 3040:2016 | Geometrical product specifications (GPS) Dimensioning and tolerancing Cones |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.