BS 5131-1.3:1991
Current
The latest, up-to-date edition.
Methods of test for footwear and footwear materials. Adhesives Preparation of test assemblies using adhesives (other than hot melt adhesives) for heat resistance (creep) and peel tests
Hardcopy , PDF
English
28-02-1991
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Committees responsible
Method
1 Scope
2 Principle
3 Apparatus
4 Preparation of adherends
5 Preparation and application of solvent-based and
water-based adhesives
6 Bonding the test assembly
7 Storage of test assemblies
Figures
1.3/1 Preferred test assembly for creep testing
1.3/2 Plan of allowed test assembly for creep testing
1.3/3 Allowed test assembly for creep testing where
mechanical surface preparation is not required
1.3/4 Plan of preferred test assembly for peel testing
1.3/5 Plan of allowed test assembly for peel testing
1.3/6 Allowed test assembly for peel testing where
mechanical surface preparation is not required
Methods for preparation of test assemblies required by Sections 1.1 and 1.2.
| Committee |
TCI/69
|
| DevelopmentNote |
Supersedes BS 5131-1.1.3(1976) & 89/36218 DC. (07/2005) Reviewed and confirmed by BSI, January 2011. (12/2010)
|
| DocumentType |
Standard
|
| Pages |
18
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
This Section of BS 5131 describes methods for preparation of the test assemblies required by Sections 1.1 and 1.2 for determination, respectively, of the resistance of bonded joints to heat (creep test) and to peeling. This Section includes methods for preparation of the adhesive and of the adherends. It covers most types of bonding used in the footwear industry except hot melt adhesive bonds which are covered in Section 1.7.
The types of bond include stuck-on bonds made by the use of applied adhesives (both solvent-based and water-based), injected-on bonds using thermoplastic sole materials, e.g. polyvinylchloride (PVC), thermoplastic rubber, and moulded-on direct vulcanized rubber sole bonds. The methods of preparation are applicable to a wide variety of combinations of materials, but the peel and creep tests of Sections 1.1 and 1.2 require at least one adherend to be flexible.
NOTE The titles of the publications referred to in this standard are listed on the inside back cover.
| BS 5131-1.1:1991 | Methods of test for footwear and footwear materials. Adhesives Resistance of adhesive joints to heat (creep test) |
| BS 5131-1.2:1991 | Methods of test for footwear and footwear materials. Adhesives Resistance of adhesive joints to peeling |
| BS 5131-1.7:1991 | Methods of test for footwear and footwear materials. Adhesives Preparation of test assemblies using hot melt adhesives for heat resistance (creep) and peel tests |
| BS 5131-1.2:1991 | Methods of test for footwear and footwear materials. Adhesives Resistance of adhesive joints to peeling |
| BS 871:1981 | Specification for abrasive papers and cloths |
| BS 5131-0:1990 | Methods of test for footwear and footwear materials General introduction |
| BS 5131-1.7(1981) : LATEST | METHODS OF TEST FOR FOOTWEAR AND FOOTWEAR MATERIALS - ADHESIVES - THE PREPARATION OF HOT MELT ADHESIVE BONDED ASSEMBLIES FOR HEAT RESISTANCE (CREEP) AND PEEL TESTS |
| BS 903-A26:1969 | Physical testing of rubber Determination of hardness |
| BS 5131-1.1:1991 | Methods of test for footwear and footwear materials. Adhesives Resistance of adhesive joints to heat (creep test) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.