BS 6160-1:1989
Current
The latest, up-to-date edition.
Radio equipment used in mobile services General requirements and conditions of measurement
Hardcopy , PDF
English
29-09-1989
National foreword
Committees responsible
1. Scope
2. Object
Section one - Terminology
3. General terms and definitions
4. Terms and definitions related to the equipment
5. Terms and definitions related to the performance
of the equipment
Section two - General conditions of measurement
6. General requirements, concerning the measuring
equipment
7. Standard test conditions
Section three - Operating conditions
8. Basic equipment
9. Associated equipment
10. Special function sub-systems
11. Standard test modulation
12. Supplementary operating conditions
Section four - Standard conditions for the primary power
supply
13. General
14. Standard d.c. test voltage for equipment supplied
by accumulator batteries which are normally charged
when the equipment is in operation (Category A)
15. Standard d.c. test voltage for equipment supplied
either by primary cells or batteries, or accumulator
batteries which are not charged while the equipment
is in operation (Categories B and C)
16. Standard a.c. voltage and frequency for equipment
using other power supplies
17. Standard d.c. test voltage for portable vehicle
equipment (Category A/B)
Section five - Standard atmospheric conditions
18. General
19. Standard atmospheric testing conditions
20. Standard atmospheric reference conditions
21. Standard atmospheric referee conditions
Section six - Standard daily duty-cycle conditions
22. Continuous operation of base equipment or vehicle
equipment (Category A)
23. Intermittent operation of vehicle equipment
(Category A)
24. Intermittent operation of portable and personal
equipment (Categories A/B, B and C)
Section seven - Evaluation of the performance of the
equipment under conditions deviating from standard test
conditions
25. General
Section eight - Initial measurements under standard test
conditions
26. General
27. Variation of primary power supply voltage range
within the specified range
28. Temperature range
29. Humidity
30. Other environmental conditions
Section nine - Useful battery life
31. Scope
32. Definitions
33. Conditions of measurement
34. Method of measurement
35. Presentation of the results
Section ten - Size and weight
36. Definition of size
37. Method of measurement
38. Definition of weight
39. Method of measurement
Gives detailed methods of making measurements selected and recommended for assessing the essential properties of the equipment but is not mandatory that measurements of all the defined characteristics be made. Suitable for radio transmitting and receiving equipment and systems used in the mobile services. Limited to land and mobile stations in the mobile services and to portable and personal equipment which operates in one or more radio-frequency channels below 1000 MHz and is intended for the transmission and the reception, either in a simplex or a duplex mode, of emissions modulated by a single information channel.
Committee |
W/-
|
DevelopmentNote |
Also numbered as IEC 60489-1 Supersedes 81/26903 DC and BS 6160-1(1981) (09/2005)
|
DocumentType |
Standard
|
Pages |
28
|
PublisherName |
British Standards Institution
|
Status |
Current
|
Supersedes |
This standard applies to radio transmitting and receiving equipment and systems used in the mobile services.
This standard is restricted to land and mobile stations in the mobile services and to portable and personal equipment which may operate in one or more radio-frequency channels in the frequency range below 1 000 MHz and is intended for the transmission and the reception, either in a simplex or a duplex mode, of emissions modulated by a single information channel.
In this standard, the equipment includes the aerial (antenna) change-over device or the duplexer, if used, but does not include:
- the aerial (antenna) or aerial (antenna) system except in the case of equipment using integral aerials (antennas);
- the input transducer of the transmitter;
- the output transducer of the receiver except in the case of equipment using integral transducers (see note).
NOTE The performance of the equipment depends upon that of the input and the output transducers used. Assessing the performance of these transducers may be the subject of separate measurements which are outside the scope of this standard.
This standard also provides for testing certain special sub-systems (see Clause 10).
BS 2011-2.1A:1977 | Environmental testing. Tests Tests A. Cold |
BS 2011-2.1B:1977 | Environmental testing. Tests Tests B. Dry Heat |
BS 2011-2.1Ed:1977 | Environmental testing. Tests Test Ed. Free fall |
BS 2011-2.1Ca:1977 | Environmental testing. Tests Test Ca. Damp heat, steady state |
BS 4727(1971) : LATEST | |
IEC 60244-1:1999 | Methods of measurement for radio transmitters - Part 1: General characteristics for broadcast transmitters |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.