• There are no items in your cart

BS 6201-3:1982

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Fixed capacitors for use in electronic equipment Specification for fixed capacitors for radio interference suppression. Selection of methods of test and general requirements

Available format(s)

Hardcopy , PDF

Superseded date

15-01-1995

Language(s)

English

Published date

31-12-1982

National foreword
Cooperating organizations
Section one - General
1 Scope
2 Object
3 Related documents
4 Terminology
Section two - Preferred ratings and characteristics
5 Preferred ratings and characteristics
6 Marking
Section three - Requirements for tests and measuring
                methods
7 Qualification approval tests
8 Schedules for qualification approval tests
9 Standard atmospheric conditions for testing
10 Visual examination and check of dimensions
11 Electrical tests
11.1 Voltage proof
11.2 Capacitance
11.3 Insulation resistance
12 Environmental tests
12.1 Robustness of terminations
12.2 Resistance to soldering heat
12.3 Solderability (not applicable to terminations of
       snap-on contacts)
12.4 Rapid change of temperature
12.5 Vibration
12.6 Bump
12.7 Shock
12.8 Container sealing (when prescribed in the detail
       specification)
12.9 Climatic sequence
12.10 Damp heat, steady state
12.11 Endurance
12.12 Charge and discharge (applies only to metallized
       film or metallized paper capacitors)
12.13 Radio-frequency characteristics
Appendices
A Example of a suitable circuit for the pulse test
B Example of a suitable circuit for the endurance
       test for a.c. capacitors
C Example of a suitable circuit for the charge and
       discharge test
D Guide to the application of radio interference
       suppression capacitors (under consideration)

Establishes requirements for electrical shock hazard protection and prescribes standard ratings and characteristics, also methods of test and general requirements for this type of capacitor.

Committee
W/-
DevelopmentNote
REPLACES BS 2135:1966.
DocumentType
Standard
Pages
32
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

BS 7314:1990 Specification for electric stunners for poultry
BS QC 300100:1991 Harmonized system of quality assessment for electronic components. Fixed capacitors for use in electronic equipment. Sectional specification: fixed polyethylene-terephthalate film dielectric metal foil d.c. capacitors
BS 5724-2.35(1997) : 1997 MEDICAL ELECTRICAL EQUIPMENT - PARTICULAR REQUIREMENTS FOR SAFETY - SPECIFICATION FOR BLANKETS, PADS AND MATTRESSES INTENDED FOR HEATING AND MEDICAL USE
BS CECC 31600:1991 Harmonized system of quality assessment for electronic components: sectional specification. Fixed capacitors with paper and paper/plastics dielectrics
BS EN 61049:1993 Specification for capacitors for use in tubular fluorescent and other discharge lamp circuits. Performance requirements
BS QC 300900:1991 Harmonized system of quality assessment for electronic components. Fixed capacitors for use in electronic equipment. Sectional specification: fixed polystyrene film dielectric metal foil d.c. capacitors
BS 9930-12.0(1983) : AMD 5952 SPEC FOR HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - FIXED CAPS FOR USE IN ELECTRONIC COMPS - SEC SPEC: FIXED METALLIZED POLYPROPYLENE FILM DIELECTRIC D.C. CAPACITORS
BS 5724-1(1989) : 1989 AMD 6715 MEDICAL ELECTRICAL EQUIPMENT - GENERAL REQUIREMENTS FOR SAFETY
BS CECC 30400:1984 Harmonized system of quality assessment for electronic components. Sectional specification: fixed metallized polyethylene-terephthalate film dielectric capacitors for direct current
BS 5076:1974 Specification for hospital storage cabinets for bottled fluids (electrically heated)
BS CECC 32200:1989 Harmonized system of quality assessment for electronic components. Sectional specification: fixed chip capacitors with metallized electrodes and polyethylene-terephthalate dielectric for direct current
BS EN 61011:1993 Electric fence energizers. Safety requirements for mains-operated electric fence energizers
DD ENV 1954:1997 Internal and external fault behaviour of safety related electronic parts of gas appliances
BS 9930-04.0(1983) : 1983 SECTION SPECIFICATION: FIXED METALLIZED POLYETHYLENE TEREPHTHALATE FILM DIELECTRIC D.C. CAPACITORS
BS EN 60601-2-35:1997 Medical electrical equipment. Particular requirements for safety Specification for blankets, pads and mattresses intended for heating in medical use
BS QC 301700:1992 Harmonized system of quality assessment for electronic components. Fixed capacitors for use in electronic equipment. Sectional specification for fixed polycarbonate film dielectric metal foil d.c. capacitors
BS QC 300400:1983 Harmonized system of quality assessment for electronic components. Fixed capacitors for use in electronic equipment. Sectional specification: fixed metallized polyethylene terephthalate film dielectric d.c. capacitors
BS QC 301800:1991 Harmonized system of quality assessment for electronic components. Fixed capacitors for use in electronic equipment. Sectional specification for fixed polypropylene film dielectric metal foil d.c. capacitors

BS 3456-101:1978 Specification for safety of household and similar electrical appliances General requirements
IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
IEC 60068-2-27:2008 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
IEC 60068-2-20:2008 Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
BS 2011-2.1Ea:1977 Environmental testing. Tests Test Ea. Shock
BS 6201-2:1982 Fixed capacitors for use in electronic equipment. Specification for fixed capacitors of ceramic dielectric, Class 2. Selection of methods of test and general requirements
BS 923-1:1980 Guide on high-voltage testing techniques General
IEC 60384-1:2016 Fixed capacitors for use in electronic equipment - Part 1: Generic specification
IEC 60384-9:2015 Fixed capacitors for use in electronic equipment - Part 9: Sectional specification: Fixed capacitors of ceramic dielectric, Class 2
BS 6201-1:1982 Fixed capacitors for use in electronic equipment Methods of test
IEC 60068-2-17:1994 Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing
IEC 60062:2016 Marking codes for resistors and capacitors
IEC 60063:2015 Preferred number series for resistors and capacitors
IEC 60060-1:2010 High-voltage test techniques - Part 1: General definitions and test requirements
IEC 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)

€231.38
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.